Wikipedia

76 mm gun M1

(Redirected from 76 mm gun M1A2)

The 76 mm gun M1 was an American World War II–era tank gun developed by the U.S United States Ordnance Department in 1942 to supplement the 75 mm gun on the basic Medium tank M4. It was also used to arm the M18 Hellcat tank destroyer.

76 mm gun M1
An M18 Hellcat armed with a 76 mm gun
TypeTank gun
Place of originUnited States
Service history
Used byUnited States
Wars
Production history
DesignerUS Ordnance Department
Specifications
Mass1,141 lb (517.55 kg)
Barrel length52 calibres
ShellFixed QF 76.2×539mm R[citation needed]
(R/93mm)
Caliber76.2 millimetres (3.00 in)

Although the gun was tested in early August 1942 and classified on 17 August 1942,[1] it was not until August 1943[2] that the Ordnance Department developed a mounting for the M4 tank that the tank forces would accept. It was not accepted for combat until July 1944.[3] In January 1943, the decision was made to mount the 76 mm on the vehicle that would become the M18.[4] By May 1944, it was being combat tested as the T70.[5] Overall the weapon performed poorly against comparable guns of the time and was used as a stopgap until the 90mm entered service.

Design and development

edit

Before the United States had battle experience against heavily armored German tanks, the development of a weapon superior to the 75 mm gun was anticipated. The original Ordnance Department specifications of 11 September 1941 for the M4 tank allowed for the mounting of numerous weapons including the 3 inch gun.[6] The first specimens of the weapon that was to become the 76 mm Gun M1 were being evaluated in August 1942 while the U.S. did not enter the ground war in the European-African-Middle Eastern region until Operation Torch in November 1942.[a]

The 3 inch gun, based on the 3-inch gun M1918 anti-aircraft gun, was considered too large and heavy[6] at about 1,990 lb (900 kg)[7] for mounting in the M4 tank. New stronger steels [8] were used to create a weapon of similar performance weighing about 1,200 lb (540 kg).[9] It was a new gun with a breech similar to that of the 75 mm M3 Gun but with a new tube (barrel and cartridge chamber) design to accommodate a new cartridge.[6] It fired the same projectiles as the 3-inch Gun M1918 3-inch (76 mm) M7 gun mounted on the 3in Gun Motor Carriage M10 tank destroyer and towed 3-inch Gun M5 anti-tank gun, but from a different cartridge case.[6] The "76-mm" designation was chosen to help keep the supply of ammunition from being confused between the two guns.[10] The 76 mm also differed in that successive models received a muzzle brake and faster rifle twist.

Aberdeen Proving Ground began evaluations of the first test guns, designated the T1, around 1 August 1942.[11] The first test guns had a bore length of 57 calibers and when tested on an M4 tank; it was found that the long barrel caused balance problems.[6] Another T1 test gun was produced with the barrel shortened to 52 calibers and a counterweight added to the breech guard to improve balance.[11]

By 17 August, the Ordnance Department had classified the test gun with the shorter barrel as the 76-mm M1 [12] and set up the precedent for the designation of M4 tanks armed with the gun to include "(76M1)".[1]

Tests of production M1 guns revealed that the gun with its counterweight also had issues with binding when trying to rotate the turret when the tank was resting at a steep angle. An 800 lb (360 kg) storage box was added to the turret rear to improve balance,[1] with evaluations held in early 1943 and the final report tendered in April 1943.[13] This worked, but was rejected by the Armored Force due to the turret being cramped.[13]

A more satisfactory mounting was found in August 1943 by utilizing the turret design of the T23 tank on the M4 chassis to carry the 76 mm gun.[14] The 76 mm M1A1 version of the gun was then created, having a longer recoil surface to also help with balance by permitting the placement of the trunnions further to the front.[14]

Production and tactical doctrine

edit

By August 1943, the M4 tank armed with the 76 mm gun in the modified T23 turret was finally ready for production. A proposal was made by the Armored Force for a test run of 1,000 tanks for combat trials and, if that was successful, then devoting all M4 tank manufacturing capacity to those armed with the 76 mm gun.[2] This was changed to a rate that would equip 1/3 of the M4 tanks with the 76 mm gun.[15]

The production proposal was part of a memo in September 1943 pointing out various flaws of the gun that made it less desirable for tank use: muzzle blast, a weaker high explosive shell, more awkward ammunition handling, and ammunition storage. Summed up, the 76 mm offered about 1 inch (25 millimetres) of added armor penetrating power for a loss of some high explosive firepower.[16] In a meeting in April 1944 held to discuss the assignment of the first production M4(76M1) tanks received in Britain to units, a presentation comparing the 76 mm to the 75 mm went over similar points, adding that the 76 mm was more accurate, but did not yet have an appropriate smoke round.[17]

Muzzle blast

edit

The muzzle blast of early 76 mm guns obscured the target with smoke and dust. This could prevent the gunner from seeing where the projectile struck. The Ordnance Department initially reduced the amount of smoke by using a long primer that gave a more complete burn of the propellant before it exited the barrel.[18] The revised ammunition began to be issued for use in August 1944.[19] Muzzle brakes, that redirected the blast left and right, were tested in January 1944 and authorized in February 1944, with production starting in June 1944. Mid-production guns (M1A1C) were threaded for a muzzle brake, with the threads covered by a protector cap.[20][18] Enough muzzle brakes were produced to allow them to be released onto M4 production lines in the fall.

For those vehicles that did not have a muzzle brake, once the Armored Force began to accept M4s, it was recommended that tank commanders stand outside the tank and "spot" the strike of rounds to guide the gunner.[17]

High-explosive capacity

edit

The situation with the high-explosive shell was that the 3 inch M42 projectile for the 76 mm gun carried a filler of about 0.9 lb (0.41 kg) of explosives while the 75 mm gun M48 high explosive projectile carried 1.5 lb (0.68 kg).[21] Far more high explosive ammunition was used by tankers than armor piercing types, the proportions being about 70% HE, 20% AP and 10% smoke overall,[22] The ratio could vary by unit: From 3 August – 31 December 1944 the 13th Tank Battalion fired 55 rounds of M62 APC-T armor piercing versus 19,634 rounds of M42 high explosive.[23]

Smoke ammunition

edit

The M88 smoke round for the 76 mm provided a "curtain" of smoke.[24] The tankers found the 75 mm M64 WP (White Phosphorus) smoke projectile useful not only for providing smoke coverage but also attacking targets including enemy tanks.[25] Some units equipped with the 76 mm preferred to maintain a 75 mm armed tank on hand to provide the M88 WP projectile.[26]

Round size

edit

It was thought that the longer and heavier 76 mm might impede handling inside the tank's turret, slowing the rate of fire.[16] This may have been more of a concern than was warranted: on 22 April 1945, the crew of an M4 76 mm crew encountered an unidentified vehicle – which was actually a British scout car – in an ambush position, and the "76 roared twice in rapid succession". The British gunner stated that his vehicle had been destroyed, "before I could lay my hand on the trigger".[27]

It was also thought that the longer 76 mm would reduce ammunition capacity.[16] The 76 mm was first tested on the M4A1 series tank which carried 90 rounds of 75 mm ammunition,[28] while most other models carried 97 rounds of 75 mm.[29] The 76 mm cartridge reduced this to 83 rounds.[1] By late 1943, the Army had adopted the wet storage system of water containers among the rounds, to reduce fires and for the 76 mm gun this provided 71 rounds of ammunition, while the 75 mm could carry 104 rounds.[30] Storage depended on organization: The 76-mm T72 Gun Motor Carriage, designed to mount the 76-mm on the M10 GMC chassis in a T23 turret lightened for the job, carried 99 rounds (but not in wet storage).[31]

Operational history

edit

US service

edit

The 76 mm gun saw first use in a test batch of M18 Hellcat gun motor carriages in Italy in May 1944, under their development designation T70.[32] The moderate performance of the 76 mm gun by 1944 standards was one of three reasons the plans for M18 production were cut from 8,986 to 2,507, of which 650 were converted to unarmed utility vehicles.[33] An experiment was performed mounting the 90-mm armed M36 turret on an M18 to provide more firepower than the 76-mm.[34]

The first M4 tanks armed with 76 mm guns intended for combat were produced in January 1944.[35] Tanks equipped with the gun began arriving in Britain in April 1944.[17] The issue with muzzle blast had not been addressed and higher-level commanders had doubts about the use of, let alone need for, the new weapon.[17] The medium-velocity 75 mm M3 gun, which first armed the standard M4 Sherman, was quite capable of dealing with most of the German armored fighting vehicles met in 1942 and 1943, and had better high explosive capability and fewer issues with muzzle blast. It was not until July 1944 that a call for M4s armed with 76 mm guns was put out in France after unexpectedly high losses by US tank units and the arrival of numerous Panther tanks on the US sector of the front.[3]

Deliveries of the 76-mm armed tanks lagged such that by January 1945 they made up only 25% of the tanks in Europe. Plans were made by field units to directly replace the 75s on some tanks using a weight welded to the turret rear to balance it. A prototype was built, but the supply of ready-made tanks increased and that project ended.[36]

The 75 mm armed M4 tanks were never completely replaced during the war with some units in Europe still had about a 50/50 mix.[37] Units in Italy readily accepted the 76 mm,[38] but were never shipped as many as desired.[39] The US units in the Pacific Theater relied mainly on the 75 mm gun.[40] The 76 mm-armed M18 did see use in the Pacific late in the war.[41]

Performance

edit

Crew members of destroyed M4A3 tanks reported direct hits with 76 mm tank fire bouncing off turret and front slope plates of enemy tank, which is further proof of inability of present medium tanks to successfully fight the German Mark VI tank.

Unit History, 781st Tank Battalion pages 9 of 47, 1945-01-19

The 76 mm M1, while an improvement over the previous 75 mm, proved to be a disappointment in its performance against the Panther tank and upgraded models of the Panzer IV Ausf. H/J in the frontal arcs. This was the case of the 76 mm M1 versus the frontal armor of these tanks only. The other arcs did not present a problem.[42] The cause of this was the M62A1 APC round issued with the gun.[42] Another issue surfaces on detailed analysis: a change induced by the problem with the M18 turret and the weight of the original 76/57 development gun. These caused the M18 turret to be strained by the forward weight of the barrel.[42] In production, the 76mm M1 was shortened to 52 calibers to address this issue. The result was a loss in velocity and this also affected the anti-armor performance of the shell.[42] In response to the lack of performance and displeasure expressed at high levels at the lack of performance, a new shell was developed. The 76 mm M93 High-Velocity, Armor-Piercing Tracer (HVAP-T) was a large improvement being an Armor Piercing Composite Rigid shot, where the full bore, lightweight outer shell contained a slug of tungsten alloy. This improved velocity, and thus penetration, but the APCR slowed faster than the AP shot or APHE shell, such that penetration dropped below that of the previous two rounds at around 1,500 yards. The American APCR data seems to indicate that US designs were superior to German and their Soviet copies in retaining their velocity to longer ranges. The US Army did not adopt the APDS shot until the middle 1950s as the British designs were less accurate, having significant problems of dispersion from point of aim.

In the ETO armor engagements took place at ranges up to 890 yards.[42] The shell brought Panzer IV turret penetration to 1,850 yards. The Panther remained immune in the frontal arc. The side and rear arcs remained vulnerable out to 2,500 yards.[42] What was missing to achieve the penetration at 890 yards that the US Army desired against the Panther was 500 fps in velocity, 3400 fps vs. the required 3900 fps.[42]

British service

edit

The UK had developed a more effective anti-tank gun before the 76 mm gun became widely available. Although only slightly longer at 55 calibers, their Ordnance QF 17 pounder (76.2 mm) anti-tank gun had a much larger 76.2×583mmR cartridge case, which used about 5.5 lb (2.5 kg) more propellant. The anti-tank performance of the 76 mm was inferior to the British 17-pounder, more so if the latter was using APDS discarding sabot rounds, though with that ammunition the 17-pounder was less accurate than the 76 mm. The 17-pounder was also much larger and had a longer recoil than the 76 mm, which required a redesign of the turret and despite this, made the turret very cramped. The 17-pounder also had a less effective HE round. The 76 mm gunned Shermans supplied to the British were only used in Italy or by the Polish 1st Armoured Division in north-west Europe. The British and Commonwealth units in north-west Europe supported their 75 mm gunned Shermans with 17-pounder armed Sherman Fireflies.

Soviet service

edit

The first 76-mm-armed Shermans started to reach Red Army units in late summer 1944. In 1945, some units were standardized to depend mostly on them, transferring their T-34s to other units. Parts of the Polish First Army also briefly used M4A2 (76 mm) tanks, borrowed from the Red Army after heavy losses in the conquest of Danzig.

After World War II

edit

Korea

edit

By the end of 1950, more than 500 76mm gun M4A3E8 tanks were in Korea. These 76 mm-armed Shermans served well in the Korean War and, having better crew training and gun optics, had little problem piercing the armor of North Korean-manned T-34/85 tanks when firing HVAP rounds, which were amply supplied to units.[43] Some 76mm-armed M4s [44] and M18s were distributed around the world and used by other countries post-war.[45] The 76mm gun was sometimes replaced by a more powerful weapon in service with other nations after World War II.[6][43][45]

Israel

edit

France delivered 76mm-gunned Sherman tanks to Israel which used them in Operation Kadesh against Egypt in 1956 and in the 1967 Six day war, particularly in the conquest of Jerusalem. Some were still used as bulldozer tanks in the Yom Kippur War in 1973.

The Balkans

edit

Some M4A3E4s, retrofitted with the M1A1 76mm gun, as well as a few M18s, were used by various sides during the civil conflicts of former Yugoslavia during the 1990s.

India and Pakistan

edit

Pakistan bought 547 M4A1E6(76)s during the 1950s and used them in 1965 and 1971 Indo-Pakistani Wars with neighbouring India, which also fielded Sherman tanks (M4A3E4s) as well.

Uganda

edit

Uganda purchased a few ex-Israeli M4A1(76)Ws and used them during the Idi Amin regime up until the Ugandan-Tanzanian War.

Variants

edit
  • T1: Originally 57 calibers long gun,[6] reduced to 52 calibers after tests in effort to improve balance[11]
  • M1: 52 calibers long version of gun adopted for use [1]
  • M1A1: M1 with longer recoil surface to allow it to be mounted on trunions placed 12 inches further forward[14]
  • M1A1C: M1A1 threaded for muzzle brake [18]
  • M1A2: M1A1C with rifling twist changed from 1:40 calibers to 1:32 calibers[46]

A muzzle brake was tested in January 1944, authorized in February 1944 with production starting June 1944. Not all guns received them. The threads of those without a brake were covered by a protector visible in many pictures.[20]

From 1943, at the instigation of the head of the Armored Force General Jacob Devers, US Ordnance worked on a towed anti-tank gun based on the barrel of the M1, known as "76 mm gun T2 on carriage T3". Later interest in the project declined and the program was officially cancelled in 1945.[47]

Ammunition

edit

While the 76 mm had less High Explosive (HE) and smoke performance than the 75 mm, the higher-velocity 76 mm gave better anti-tank performance, with firepower similar to many of the armored fighting vehicles it encountered, particularly the Panzer IV tank and StuG assault gun vehicles. Using the M62 APC round, the 76 mm gun penetrated 109 mm (4.3 in) of armor at 0° obliquity at 1,000 m (3,300 ft), with a muzzle velocity of 792 m/s (2,600 ft/s). The HVAP round was able to penetrate 178 mm (7.0 in) at 1,000 m (3,300 ft), with a muzzle velocity of 1,036 m/s (3,400 ft/s).[48]

Round summary[24][49]
Projectile Complete round Projectile weight Filler/core Muzzle velocity Range
M42A1 HE 22.11 lb (10.03 kg) 12.87 lb (5.84 kg) 0.86 lb (0.39 kg) 2,700 ft/s (820 m/s) 14,650 yd (13,400 m)
M62A1 APC 24.55 lb (11.14 kg) 15.43 lb (7.00 kg) 0.144 lb (0.065 kg) 2,600 ft/s (790 m/s) 16,100 yd (14,700 m)
M79 AP 24.24 lb (11.00 kg) 15 lb (6.8 kg) None 2,600 ft/s (790 m/s) 12,770 yd (11,680 m)
M88 Smoke 13.43 lb (6.09 kg) 7.6 lb (3.4 kg) 3.3 lb (1.5 kg) 900 ft/s (270 m/s) 2,000 yd (1,800 m)
T4 (M93) HVAP (APCR) 7.6 lb (3.4 kg) 3.9 lb (1.8 kg) 3,400 ft/s (1,000 m/s)

The M42A1 High Explosive shell contained a 0.86 lb (0.39 kg) explosive filler of TNT or a 0.85 lb (0.39 kg) mixture of 0.08 lb (0.036 kg) of cast TNT and 0.77 lb (0.35 kg) 50/50 Amatol.[49] A reduced charge load existed with a velocity of 1,550 ft/s (470 m/s) and range of 8,805 yd (8,051 m).[50]

The standard M62A1 Armor Piercing Capped projectile was of the APCBC design.[49]

The substitute standard M79 Armor Piercing solid monobloc shot had no filler, windscreen, or penetrating cap.[49]

The M88 H.C. B.I. Smoke Shell contained a filler of H.C.[49] Based on a British design, it was intended to provide a slow-release "curtain" of smoke versus the exploding white phosphorus shell available to the 75-mm and other cannon originally designed for artillery spotting but which could also cause damaging burns.[24]

The M26 brass cartridge case was used for all loaded rounds, with a weight of 5.28 lb (2.39 kg) and length of 21.3 in (54 cm).[51] It was an entirely different case from the 3-inch MKIIM2 case used for the 3-inch M3 anti-aircraft gun and 3-inch M5, M6, and M7 guns used on the a towed anti-tank gun, M6 heavy tank, and M10 Gun Motor Carriage.[52] The 76-mm chamber capacity varied by projectile (also given is the capacities for similar 3-inch rounds to illustrate the size differences):

76-mm M1 vs 3-inch M3/5/6/7, chamber capacities
Gun M42 HE M62 APC M79 AP M88 H.C. B.I.
76-mm M1[49] 140.5 cu in (2,302 ml) 142.6 cu in (2,337 ml) 143.66 cu in (2,354.2 ml) 143.6 cu in (2,353 ml)
3-inch M3/5/6/7[53] 203.5 cu in (3,335 ml) 205.585 cu in (3,368.93 ml) 203.5 cu in (3,335 ml) None

The 3 inch cartridge was not completely filled by the propellants used; a distance wad was used to keep the propellant pressed against the primer end.[52] By way of comparison the 75 mm M3 gun had a chamber capacity of about 88 cu in (1,440 cc) for the M61 armor piercing projectile and about 80 cu in (1.3 L) for the M48 high explosive projectile [54] and the British 17pdr 300 cu in (4.9 L).[55]

Vehicles mounting the 76 mm

edit
 
A T23 turret used on 76 mm gunned Shermans, here without the muzzle brake

With British Commonwealth designations in parentheses:

Performance

edit
Penetration of armor at 30 degrees from vertical[9][56]
Ammunition 500 yards 1,000 yards 1,500 yards 2,000 yards
APC M62 Projectile (APCBC/HE-T) 93–94 mm 88–89 mm 81–82 mm 75–76 mm
AP M79 Shot (AP-T) 109 mm 92 mm 76 mm 64 mm
HVAP M93 (APCR-T) 157–158 mm 134–135 mm 116–117 mm 98–99 mm
Penetration of armor at 30 degrees from vertical[57]
Ammunition 500 m 1,000 m
M62 APC-T 98 mm 90 mm
T4 HVAP 150 mm 132 mm
Calculated penetration at range (90 degrees) using American and British 50% success criteria[58]
Ammunition type Muzzle velocity Penetration (mm)
100 m 250 m 500 m 750 m 1000 m 1250 m 1500 m 1750 m 2000 m 2500 m 3000 m
M62 versus FHA 792 m/s
(2,600 ft/s) 		124 123 122 119 116 113 110 105 101 92 83
M62 versus RHA 792 m/s
(2,600 ft/s) 		125 121 116 111 106 101 97 93 89 81 74
M79 versus FHA 792 m/s
(2,600 ft/s) 		132 124 112 101 92 83 75 68 62 50 41
M79 versus RHA 792 m/s
(2,600 ft/s) 		154 145 131 119 107 97 88 79 72 59 48
M93 1,036 m/s
(3,400 ft/s) 		239 227 208 191 175 160 147 135 124 108 88

Similar, alternative weapons

edit

The 76 mm M1 was a project initiated by the Ordnance Department itself.[2] Various entities suggested other weapon options which were not pursued.

  • In October 1942, the Aberdeen-based Ballistics Research Laboratory suggested that research begin into two options: (1) arming the M4 medium tank with the 90 mm gun (if need be by altering the cartridge case and gun) and (2) designing a 3-inch gun firing a 15 lb (6.8 kg) shot at 915 m/s (3,000 ft/s).[59]
  • The Armored Board (the Armored Forces evaluation center at Fort Knox)[16] suggested the production of 1,000 M4 medium tanks armed with 90-mm guns in the fall of 1943.[59]
  • The British expressed interest in mounting their 17-pounder on the M4 in August 1943, offering a monthly allotment of 200 weapons and ammunition, which could begin three months following acceptance.[60] By the time that the US took this up in 1944, the British were too busy with their own conversions resulting in the Sherman Firefly.[3] Some conversions destined for the US Army were performed in 1945 but did not see combat.[39]

See also

edit

Weapons of comparable role, performance and era

edit

Notes

edit
  1. ^ The first 75mm guns were used in combat with British forces (in the M3 Medium tank) earlier in 1942
  1. ^ a b c d e Hunnicutt 1978, page 200
  2. ^ a b c Zaloga 2003, page 6
  3. ^ a b c Zaloga 2003, page 16
  4. ^ Zaloga 2004, page 7
  5. ^ Zaloga 2004, page 14
  6. ^ a b c d e f g Hunnicutt 1978, page 198
  7. ^ Hunnicutt 1978, page 563
  8. ^ Green 1955, page 237
  9. ^ a b Hunnicutt 1978, page 564
  10. ^ Zaloga 2003, page 4
  11. ^ a b c Hunnicutt 1978, page 199
  12. ^ Hunnicutt 1978, page 200 picture caption
  13. ^ a b Hunnicutt 1978, page 202
  14. ^ a b c Hunnicutt 1978, page 204
  15. ^ Zaloga 2003, page 8
  16. ^ a b c d Zaloga 2008, page 116
  17. ^ a b c d Zaloga 2003, page 12
  18. ^ a b c Hunnicutt 1978, page 206
  19. ^ Zaloga 2003, page 18
  20. ^ a b Zaloga 2004, page 13
  21. ^ Ordnance Department 1944, pages 356, 359
  22. ^ Zaloga 2003, page 7
  23. ^ Green 2007, page 118
  24. ^ a b c Leventhal 1996, p 288
  25. ^ Green 2007, page 81 using the wrong designation "M89"
  26. ^ Zaloga 1978, pages 37-38
  27. ^ Hunnicutt 1978, page 322
  28. ^ Hunnicutt 1978, page 540
  29. ^ Hunnicutt 1978, pages 538, 542, 544, 549
  30. ^ Hunnicutt 1978, pages 260, 261
  31. ^ a b Hunnicutt 1978, page 376
  32. ^ Zaloga 2004, page 14
  33. ^ Zaloga 2004, page 12
  34. ^ Zaloga 2004, page 38
  35. ^ Zaloga 2003, page 10
  36. ^ Zaloga 2003, page 33
  37. ^ Zaloga 2003, page 22
  38. ^ Zaloga 2003, page 36
  39. ^ a b Zaloga 2003, page 35
  40. ^ Zaloga 2003, page 37
  41. ^ Zaloga 2004, page 34
  42. ^ a b c d e f g Cosme, Jose; Ranu, Jeff; Spickert-Fulton, Shawn (January 2018). "The 76-MM gun M1A1 and M1A2: An analysis of U.S. Anti-Tank capabilities during World War II" (PDF). Defense Technical Information Center. AD-E403 980. Archived (PDF) from the original on 27 July 2019.
  43. ^ a b Zaloga 2003, page 42
  44. ^ Zaloga 2003, page 39
  45. ^ a b Zaloga 2003, page 41
  46. ^ Hunnicutt 1978, page 207
  47. ^ Zaloga 2005, page 20
  48. ^ Zaloga, Steven. T-34-85 vs. M26 Pershing: Korea 1950. London: Osprey Publishing, 2010. pages 32-33.
  49. ^ a b c d e f Leventhal 1996, p 287
  50. ^ Ordnance Department 1944, page 128
  51. ^ Ordnance Department 1944, page 124
  52. ^ a b Ordnance Department 1944, page 132
  53. ^ Leventhal 1996, p 283,284
  54. ^ Hunnicutt 1978, page 562
  55. ^ Hunnicutt 1978, page 565
  56. ^ Bovington Tank Museum (1975). Fire and Movement. Page 23.
  57. ^ Steven J. Zaloga and Peter Sarson (1993). Sherman Medium Tank. Page 14.
  58. ^ Bird, Lorrin Rexford; Livingston, Robert D. (2001). WWII Ballistics: Armor and Gunnery. Overmatch Press. p. 63.
  59. ^ a b Hunnicutt 1978, page 212
  60. ^ Zaloga 2003, page 9

References

edit
  • Green, Constance; Thomson, Harry; Roots, Peter (1955). The Ordnance Department: Planning Munitions for War CMH Pub 10-9. Center for Military History.
  • Green, Michael; Brown, James (2007). M4 Sherman at War. Zenith Press. ISBN 9780760327845.
  • Hunnicutt, R.P. (1978). Sherman: A History of the American Medium Tank. Echo Point Books and Media, LLC. ISBN 9781626548619.
  • Leventhal, Lionel (1996). The American Arsenal. Greenhill Books, London. Stockpile Books, Pennsylvania. ISBN 1853672548.
  • Ordnance Department, United States (1944). TM 9-1901 Artillery Ammunition June 1944. War Department.}
  • Zaloga, Steven (1993). Sherman Medium Tank 1942-45. New Vanguard 3. Osprey Publishing. ISBN 185532296X.
  • Zaloga, Steven (2003). M4 (76mm) Sherman Tank 1943-65. New Vanguard 73. Osprey Publishing. ISBN 9781841765426.
  • Zaloga, Steven (2004). M18 Hellcat Tank Destroyer 1943-97. New Vanguard 97. Osprey Publishing. ISBN 1841766879.
  • Zaloga, Steven (2005). US Anti-tank Artillery 1941–45. New Vanguard 107. Osprey Publishing. ISBN 1-84176-690-9.
  • Zaloga, Steven (2008). Armored Thunderbolt: The U.S. Army Sherman in World War II. Stackpole Books. ISBN 9780811704243.

Further reading

edit
  • TM 9-308
  • SNL C-46
  • SNL C-58
  • SNL C-64
edit
 
Wikimedia Commons has media related to 76 mm gun M1.
Retrieved from "https://en.wikipedia.org/w/index.php?title=76_mm_gun_M1&oldid=1257915118#Variants"