List of semiconductor materials

(Redirected from Compound semiconductors)

Semiconductor materials are nominally small band gap insulators. The defining property of a semiconductor material is that it can be compromised by doping it with impurities that alter its electronic properties in a controllable way.[1] Because of their application in the computer and photovoltaic industry—in devices such as transistors, lasers, and solar cells—the search for new semiconductor materials and the improvement of existing materials is an important field of study in materials science.

Most commonly used semiconductor materials are crystalline inorganic solids. These materials are classified according to the periodic table groups of their constituent atoms.

Different semiconductor materials differ in their properties. Thus, in comparison with silicon, compound semiconductors have both advantages and disadvantages. For example, gallium arsenide (GaAs) has six times higher electron mobility than silicon, which allows faster operation; wider band gap, which allows operation of power devices at higher temperatures, and gives lower thermal noise to low power devices at room temperature; its direct band gap gives it more favorable optoelectronic properties than the indirect band gap of silicon; it can be alloyed to ternary and quaternary compositions, with adjustable band gap width, allowing light emission at chosen wavelengths, which makes possible matching to the wavelengths most efficiently transmitted through optical fibers. GaAs can be also grown in a semi-insulating form, which is suitable as a lattice-matching insulating substrate for GaAs devices. Conversely, silicon is robust, cheap, and easy to process, whereas GaAs is brittle and expensive, and insulation layers cannot be created by just growing an oxide layer; GaAs is therefore used only where silicon is not sufficient.[2]

By alloying multiple compounds, some semiconductor materials are tunable, e.g., in band gap or lattice constant. The result is ternary, quaternary, or even quinary compositions. Ternary compositions allow adjusting the band gap within the range of the involved binary compounds; however, in case of combination of direct and indirect band gap materials there is a ratio where indirect band gap prevails, limiting the range usable for optoelectronics; e.g. AlGaAs LEDs are limited to 660 nm by this. Lattice constants of the compounds also tend to be different, and the lattice mismatch against the substrate, dependent on the mixing ratio, causes defects in amounts dependent on the mismatch magnitude; this influences the ratio of achievable radiative/nonradiative recombinations and determines the luminous efficiency of the device. Quaternary and higher compositions allow adjusting simultaneously the band gap and the lattice constant, allowing increasing radiant efficiency at wider range of wavelengths; for example AlGaInP is used for LEDs. Materials transparent to the generated wavelength of light are advantageous, as this allows more efficient extraction of photons from the bulk of the material. That is, in such transparent materials, light production is not limited to just the surface. Index of refraction is also composition-dependent and influences the extraction efficiency of photons from the material.[3]

Types of semiconductor materials

edit

Compound semiconductors

edit

A compound semiconductor is a semiconductor compound composed of chemical elements of at least two different species. These semiconductors form for example in periodic table groups 13–15 (old groups III–V), for example of elements from the Boron group (old group III, boron, aluminium, gallium, indium) and from group 15 (old group V, nitrogen, phosphorus, arsenic, antimony, bismuth). The range of possible formulae is quite broad because these elements can form binary (two elements, e.g. gallium(III) arsenide (GaAs)), ternary (three elements, e.g. indium gallium arsenide (InGaAs)) and quaternary alloys (four elements) such as aluminium gallium indium phosphide (AlInGaP)) alloy and Indium arsenide antimonide phosphide (InAsSbP). The properties of III-V compound semiconductors are similar to their group IV counterparts. The higher ionicity in these compounds, and especially in the II-VI compound, tends to increase the fundamental bandgap with respect to the less ionic compounds.[4]

Fabrication

edit

Metalorganic vapor-phase epitaxy (MOVPE) is the most popular deposition technology for the formation of compound semiconducting thin films for devices.[citation needed] It uses ultrapure metalorganics and/or hydrides as precursor source materials in an ambient gas such as hydrogen.

Other techniques of choice include:

Table of semiconductor materials

edit
Group Elem. Material Formula Band gap (eV) Gap type Description
IV 1 Silicon Si 1.12[5][6] indirect Used in conventional crystalline silicon (c-Si) solar cells, and in its amorphous form as amorphous silicon (a-Si) in thin-film solar cells. Most common semiconductor material in photovoltaics; dominates worldwide PV market; easy to fabricate; good electrical and mechanical properties. Forms high quality thermal oxide for insulation purposes. Most common material used in the fabrication of integrated circuits.
IV 1 Germanium Ge 0.67[5][6] indirect Used in early radar detection diodes and first transistors; requires lower purity than silicon. A substrate for high-efficiency multijunction photovoltaic cells. Very similar lattice constant to gallium arsenide. High-purity crystals used for gamma spectroscopy. May grow whiskers, which impair reliability of some devices.
IV 1 Diamond C 5.47[5][6] indirect Excellent thermal conductivity. Superior mechanical and optical properties.

High carrier mobilities[7] and high electric breakdown field[8] at room temperature as excellent electronics characteristics. Extremely high nanomechanical resonator quality factor.[9]

IV 1 Gray tin, α-Sn Sn 0[10][11] semimetal Low temperature allotrope (diamond cubic lattice).
IV 2 Silicon carbide, 3C-SiC SiC 2.3[5] indirect Used for early yellow LEDs
IV 2 Silicon carbide, 4H-SiC SiC 3.3[5] indirect Used for high-voltage and high-temperature applications
IV 2 Silicon carbide, 6H-SiC SiC 3.0[5] indirect Used for early blue LEDs
VI 1 Sulfur, α-S S8 2.6[12]
VI 1 Gray (trigonal) selenium Se 1.83–2.0[13][14] indirect Used in selenium rectifiers and solar cells.[15] Band gap depends on fabrication conditions.
VI 1 Red selenium Se 2.05 indirect [16]
VI 1 Tellurium Te 0.33[17]
III-V 2 Boron nitride, cubic BN 6.36[18] indirect Potentially useful for ultraviolet LEDs
III-V 2 Boron nitride, hexagonal BN 5.96[18] quasi-direct Potentially useful for ultraviolet LEDs
III-V 2 Boron nitride nanotube BN 5.5[19]
III-V 2 Boron phosphide BP 2.1[20] indirect
III-V 2 Boron arsenide BAs 1.82 direct Ultrahigh thermal conductivity for thermal management; Resistant to radiation damage, possible applications in betavoltaics.
III-V 2 Boron arsenide B12As2 3.47 indirect Resistant to radiation damage, possible applications in betavoltaics.
III-V 2 Aluminium nitride AlN 6.28[5] direct Piezoelectric. Not used on its own as a semiconductor; AlN-close GaAlN possibly usable for ultraviolet LEDs. Inefficient emission at 210 nm was achieved on AlN.
III-V 2 Aluminium phosphide AlP 2.45[6] indirect
III-V 2 Aluminium arsenide AlAs 2.16[6] indirect
III-V 2 Aluminium antimonide AlSb 1.6/2.2[6] indirect/direct
III-V 2 Gallium nitride GaN 3.44[5][6] direct Problematic to be doped to p-type, p-doping with Mg and annealing allowed first high-efficiency blue LEDs[3] and blue lasers. Very sensitive to ESD. Insensitive to ionizing radiation. GaN transistors can operate at higher voltages and higher temperatures than GaAs, used in microwave power amplifiers. When doped with e.g. manganese, becomes a magnetic semiconductor.
III-V 2 Gallium phosphide GaP 2.26[5][6] indirect Used in early low to medium brightness cheap red/orange/green LEDs. Used standalone or with GaAsP. Transparent for yellow and red light, used as substrate for GaAsP red/yellow LEDs. Doped with S or Te for n-type, with Zn for p-type. Pure GaP emits green, nitrogen-doped GaP emits yellow-green, ZnO-doped GaP emits red.
III-V 2 Gallium arsenide GaAs 1.42[5][6] direct Second most common in use after silicon, commonly used as substrate for other III-V semiconductors, e.g. InGaAs and GaInNAs. Brittle. Lower hole mobility than Si, P-type CMOS transistors unfeasible. High impurity density, difficult to fabricate small structures. Used for near-IR LEDs, fast electronics, and high-efficiency solar cells. Very similar lattice constant to germanium, can be grown on germanium substrates.
III-V 2 Gallium antimonide GaSb 0.73[5][6] direct Used for infrared detectors and LEDs and thermophotovoltaics. Doped n with Te, p with Zn.
III-V 2 Indium nitride InN 0.7[5] direct Possible use in solar cells, but p-type doping difficult. Used frequently as alloys.
III-V 2 Indium phosphide InP 1.35[5] direct Commonly used as substrate for epitaxial InGaAs. Superior electron velocity, used in high-power and high-frequency applications. Used in optoelectronics.
III-V 2 Indium arsenide InAs 0.36[5] direct Used for infrared detectors for 1–3.8 μm, cooled or uncooled. High electron mobility. InAs dots in InGaAs matrix can serve as quantum dots. Quantum dots may be formed from a monolayer of InAs on InP or GaAs. Strong photo-Dember emitter, used as a terahertz radiation source.
III-V 2 Indium antimonide InSb 0.17[5] direct Used in infrared detectors and thermal imaging sensors, high quantum efficiency, low stability, require cooling, used in military long-range thermal imager systems. AlInSb-InSb-AlInSb structure used as quantum well. Very high electron mobility, electron velocity and ballistic length. Transistors can operate below 0.5V and above 200 GHz. Terahertz frequencies maybe achievable.
II-VI 2 Cadmium selenide CdSe 1.74[6] direct Nanoparticles used as quantum dots. Intrinsic n-type, difficult to dope p-type, but can be p-type doped with nitrogen. Possible use in optoelectronics. Tested for high-efficiency solar cells.
II-VI 2 Cadmium sulfide CdS 2.42[6] direct Used in photoresistors and solar cells; CdS/Cu2S was the first efficient solar cell. Used in solar cells with CdTe. Common as quantum dots. Crystals can act as solid-state lasers. Electroluminescent. When doped, can act as a phosphor.
II-VI 2 Cadmium telluride CdTe 1.49[6] direct Used in solar cells with CdS. Used in thin film solar cells and other cadmium telluride photovoltaics; less efficient than crystalline silicon but cheaper. High electro-optic effect, used in electro-optic modulators. Fluorescent at 790 nm. Nanoparticles usable as quantum dots.
II-VI, oxide 2 Zinc oxide ZnO 3.37[6] direct Photocatalytic. Band gap is tunable from 3 to 4 eV by alloying with magnesium oxide and cadmium oxide. Intrinsic n-type, p-type doping is difficult. Heavy aluminium, indium, or gallium doping yields transparent conductive coatings; ZnO:Al is used as window coatings transparent in visible and reflective in infrared region and as conductive films in LCD displays and solar panels as a replacement of indium tin oxide. Resistant to radiation damage. Possible use in LEDs and laser diodes. Possible use in random lasers.
II-VI 2 Zinc selenide ZnSe 2.7[6] direct Used for blue lasers and LEDs. Easy to n-type doping, p-type doping is difficult but can be done with e.g. nitrogen. Common optical material in infrared optics.
II-VI 2 Zinc sulfide ZnS 3.54/3.91[6] direct Band gap 3.54 eV (cubic), 3.91 (hexagonal). Can be doped both n-type and p-type. Common scintillator/phosphor when suitably doped.
II-VI 2 Zinc telluride ZnTe 2.3[6] direct Can be grown on AlSb, GaSb, InAs, and PbSe. Used in solar cells, components of microwave generators, blue LEDs and lasers. Used in electrooptics. Together with lithium niobate used to generate terahertz radiation.
I-VII 2 Cuprous chloride CuCl 3.4[21] direct
I-VI 2 Copper(I) sulfide Cu2S 1.2[20] indirect p-type, Cu2S/CdS was the first efficient thin film solar cell
IV-VI 2 Lead selenide PbSe 0.26[17] direct Used in infrared detectors for thermal imaging. Nanocrystals usable as quantum dots. Good high temperature thermoelectric material.
IV-VI 2 Lead(II) sulfide PbS 0.37[22] Mineral galena, first semiconductor in practical use, used in cat's whisker detectors; the detectors are slow due to high dielectric constant of PbS. Oldest material used in infrared detectors. At room temperature can detect SWIR, longer wavelengths require cooling.
IV-VI 2 Lead telluride PbTe 0.32[5] Low thermal conductivity, good thermoelectric material at elevated temperature for thermoelectric generators.
IV-VI 2 Tin(II) sulfide SnS 1.3/1.0[23] direct/indirect Tin sulfide (SnS) is a semiconductor with direct optical band gap of 1.3 eV and absorption coefficient above 104 cm−1 for photon energies above 1.3 eV. It is a p-type semiconductor whose electrical properties can be tailored by doping and structural modification and has emerged as one of the simple, non-toxic and affordable material for thin films solar cells since a decade.
IV-VI 2 Tin(IV) sulfide SnS2 2.2[24] SnS2 is widely used in gas sensing applications.
IV-VI 2 Tin telluride SnTe 0.18 direct Complex band structure.
V-VI, layered 2 Bismuth telluride Bi2Te3 0.13[5] Efficient thermoelectric material near room temperature when alloyed with selenium or antimony. Narrow-gap layered semiconductor. High electrical conductivity, low thermal conductivity. Topological insulator.
II-V 2 Cadmium phosphide Cd3P2 0.5[25]
II-V 2 Cadmium arsenide Cd3As2 0 N-type intrinsic semiconductor. Very high electron mobility. Used in infrared detectors, photodetectors, dynamic thin-film pressure sensors, and magnetoresistors. Recent measurements suggest that 3D Cd3As2 is actually a zero band-gap Dirac semimetal in which electrons behave relativistically as in graphene.[26]
II-V 2 Zinc phosphide Zn3P2 1.5[27] direct Usually p-type.
II-V 2 Zinc diphosphide ZnP2 2.1[28]
II-V 2 Zinc arsenide Zn3As2 1.0[29] The lowest direct and indirect bandgaps are within 30 meV or each other.[29]
II-V 2 Zinc antimonide Zn3Sb2 Used in infrared detectors and thermal imagers, transistors, and magnetoresistors.
Oxide 2 Titanium dioxide, anatase TiO2 3.20[30] indirect Photocatalytic, n-type
Oxide 2 Titanium dioxide, rutile TiO2 3.0[30] direct Photocatalytic, n-type
Oxide 2 Titanium dioxide, brookite TiO2 3.26[30] [31]
Oxide 2 Copper(I) oxide Cu2O 2.17[32] One of the most studied semiconductors. Many applications and effects first demonstrated with it. Formerly used in rectifier diodes, before silicon.
Oxide 2 Copper(II) oxide CuO 1.2 N-type semiconductor.[33]
Oxide 2 Uranium dioxide UO2 1.3 High Seebeck coefficient, resistant to high temperatures, promising thermoelectric and thermophotovoltaic applications. Formerly used in URDOX resistors, conducting at high temperature. Resistant to radiation damage.
Oxide 2 Tin dioxide SnO2 3.7 Oxygen-deficient n-type semiconductor. Used in gas sensors.
Oxide 3 Barium titanate BaTiO3 3 Ferroelectric, piezoelectric. Used in some uncooled thermal imagers. Used in nonlinear optics.
Oxide 3 Strontium titanate SrTiO3 3.3 Ferroelectric, piezoelectric. Used in varistors. Conductive when niobium-doped.
Oxide 3 Lithium niobate LiNbO3 4 Ferroelectric, piezoelectric, shows Pockels effect. Wide uses in electrooptics and photonics.
Oxide, V-VI 2 monoclinic Vanadium(IV) oxide VO2 0.7[34] optical Stable below 67 °C
Layered 2 Lead(II) iodide PbI2 2.4[35] PbI2 is a layered direct bandgap semiconductor with bandgap of 2.4 eV in its bulk form, whereas its 2D monolayer has an indirect bandgap of ~2.5 eV, with possibilities to tune the bandgap between 1–3 eV
Layered 2 Molybdenum disulfide MoS2 1.23 eV (2H)[36] indirect
Layered 2 Gallium selenide GaSe 2.1 indirect Photoconductor. Uses in nonlinear optics. Used as 2D-material. Air sensitive.[37][38][39]
Layered 2 Indium selenide InSe 1.26–2.35 eV[39] direct (indirect in 2D) Air sensitive. High electrical mobility in few- and mono-layer form.[37][38][39]
Layered 2 Tin sulfide SnS >1.5 eV direct
Layered 2 Bismuth sulfide Bi2S3 1.3[5]
Magnetic, diluted (DMS)[40] 3 Gallium manganese arsenide GaMnAs
Magnetic, diluted (DMS) 3 Lead manganese telluride PbMnTe
Magnetic 4 Lanthanum calcium manganate La0.7Ca0.3MnO3 Colossal magnetoresistance
Magnetic 2 Iron(II) oxide FeO 2.2[41] Antiferromagnetic. Band gap for iron oxide nanoparticles was found to be 2.2 eV and on doping the band gap found to be increased up to 2.5 eV
Magnetic 2 Nickel(II) oxide NiO 3.6–4.0 direct[42][43] Antiferromagnetic
Magnetic 2 Europium(II) oxide EuO Ferromagnetic
Magnetic 2 Europium(II) sulfide EuS Ferromagnetic
Magnetic 2 Chromium(III) bromide CrBr3
other 3 Copper indium selenide, CIS CuInSe2 1 direct
other 3 Silver gallium sulfide AgGaS2 Nonlinear optical properties
other 3 Zinc silicon phosphide ZnSiP2 2.0[20]
other 2 Arsenic trisulfide Orpiment As2S3 2.7[44] direct Semiconductive in both crystalline and glassy state
other 2 Arsenic sulfide Realgar As4S4 Semiconductive in both crystalline and glassy state
other 2 Platinum silicide PtSi Used in infrared detectors for 1–5 μm. Used in infrared astronomy. High stability, low drift, used for measurements. Low quantum efficiency.
other 2 Bismuth(III) iodide BiI3
other 2 Mercury(II) iodide HgI2 Used in some gamma-ray and x-ray detectors and imaging systems operating at room temperature.
other 2 Thallium(I) bromide TlBr 2.68[45] Used in some gamma-ray and x-ray detectors and imaging systems operating at room temperature. Used as a real-time x-ray image sensor.
other 2 Silver sulfide Ag2S 0.9[46]
other 2 Iron disulfide FeS2 0.95[47] Mineral pyrite. Used in later cat's whisker detectors, investigated for solar cells.
other 4 Copper zinc tin sulfide, CZTS Cu2ZnSnS4 1.49 direct Cu2ZnSnS4 is derived from CIGS, replacing the Indium/Gallium with earth abundant Zinc/Tin.
other 4 Copper zinc antimony sulfide, CZAS Cu1.18Zn0.40Sb1.90S7.2 2.2[48] direct Copper zinc antimony sulfide is derived from copper antimony sulfide (CAS), a famatinite class of compound.
other 3 Copper tin sulfide, CTS Cu2SnS3 0.91[20] direct Cu2SnS3 is p-type semiconductor and it can be used in thin film solar cell application.

Table of semiconductor alloy systems

edit

The following semiconducting systems can be tuned to some extent, and represent not a single material but a class of materials.

Group Elem. Material class Formula Band gap (eV) Gap type Description
Lower Upper
IV-VI 3 Lead tin telluride Pb1−xSnxTe 0 0.29 Used in infrared detectors and for thermal imaging
IV 2 Silicon-germanium Si1−xGex 0.67 1.11[5] direct/indirect Adjustable band gap, allows construction of heterojunction structures. Certain thicknesses of superlattices have direct band gap.[49]
IV 2 Silicon-tin Si1−xSnx 1.0 1.11 indirect Adjustable band gap.[50]
III-V 3 Aluminium gallium arsenide AlxGa1−xAs 1.42 2.16[5] direct/indirect Direct band gap for x<0.4 (corresponding to 1.42–1.95 eV); can be lattice-matched to GaAs substrate over entire composition range; tends to oxidize; n-doping with Si, Se, Te; p-doping with Zn, C, Be, Mg.[3] Can be used for infrared laser diodes. Used as a barrier layer in GaAs devices to confine electrons to GaAs (see e.g. QWIP). AlGaAs with composition close to AlAs is almost transparent to sunlight. Used in GaAs/AlGaAs solar cells.
III-V 3 Indium gallium arsenide InxGa1−xAs 0.36 1.43 direct Well-developed material. Can be lattice matched to InP substrates. Use in infrared technology and thermophotovoltaics. Indium content determines charge carrier density. For x=0.015, InGaAs perfectly lattice-matches germanium; can be used in multijunction photovoltaic cells. Used in infrared sensors, avalanche photodiodes, laser diodes, optical fiber communication detectors, and short-wavelength infrared cameras.
III-V 3 Indium gallium phosphide InxGa1−xP 1.35 2.26 direct/indirect Used for HEMT and HBT structures and high-efficiency multijunction solar cells for e.g. satellites. Ga0.5In0.5P is almost lattice-matched to GaAs, with AlGaIn used for quantum wells for red lasers.
III-V 3 Aluminium indium arsenide AlxIn1−xAs 0.36 2.16 direct/indirect Buffer layer in metamorphic HEMT transistors, adjusting lattice constant between GaAs substrate and GaInAs channel. Can form layered heterostructures acting as quantum wells, in e.g. quantum cascade lasers.
III-V 3 Aluminium gallium antimonide AlxGa1−xSb 0.7 1.61 direct/indirect Used in HBTs, HEMTs, resonant-tunneling diodes and some niche optoelectronics. Also used as a buffer layer for InAs quantum wells.
III-V 3 Aluminium indium antimonide AlxIn1−xSb 0.17 1.61 direct/indirect Used as a buffer layer in InSb-based quantum wells and other devices grown on GaAs and GaSb substrates. Also used as the active layer in some mid-infrared LEDs and photodiodes.
III-V 3 Gallium arsenide nitride GaAsN
III-V 3 Gallium arsenide phosphide GaAsP 1.43 2.26 direct/indirect Used in red, orange and yellow LEDs. Often grown on GaP. Can be doped with nitrogen.
III-V 3 Aluminium arsenide antimonide AlAsSb 1.61 2.16 indirect Used as a barrier layer in infrared photodetectors. Can be lattice matched to GaSb, InAs and InP.
III-V 3 Gallium arsenide antimonide GaAsSb 0.7 1.42[5] direct Used in HBTs and in tunnel junctions in multi-junction solar cells. GaAs0.51Sb0.49 is lattice matched to InP.
III-V 3 Aluminium gallium nitride AlGaN 3.44 6.28 direct Used in blue laser diodes, ultraviolet LEDs (down to 250 nm), and AlGaN/GaN HEMTs. Can be grown on sapphire. Used in heterojunctions with AlN and GaN.
III-V 3 Aluminium gallium phosphide AlGaP 2.26 2.45 indirect Used in some green LEDs.
III-V 3 Indium gallium nitride InGaN 2 3.4 direct InxGa1–xN, x usually between 0.02 and 0.3 (0.02 for near-UV, 0.1 for 390 nm, 0.2 for 420 nm, 0.3 for 440 nm). Can be grown epitaxially on sapphire, SiC wafers or silicon. Used in modern blue and green LEDs, InGaN quantum wells are effective emitters from green to ultraviolet. Insensitive to radiation damage, possible use in satellite solar cells. Insensitive to defects, tolerant to lattice mismatch damage. High heat capacity.
III-V 3 Indium arsenide antimonide InAsSb 0.17 0.36 direct Primarily used in mid- and long-wave infrared photodetectors due to its small bandgap, which reaches a minimum of around 0.08 eV in InAs0.4Sb0.6 at room temperature.
III-V 3 Indium gallium antimonide InGaSb 0.17 0.7 direct Used in some transistors and infrared photodetectors.
III-V 4 Aluminium gallium indium phosphide AlGaInP direct/indirect Also InAlGaP, InGaAlP, AlInGaP; for lattice matching to GaAs substrates the In mole fraction is fixed at about 0.48, the Al/Ga ratio is adjusted to achieve band gaps between about 1.9 and 2.35 eV; direct or indirect band gaps depending on the Al/Ga/In ratios; used for waveengths between 560 and 650 nm; tends to form ordered phases during deposition, which has to be prevented[3]
III-V 4 Aluminium gallium arsenide phosphide AlGaAsP
III-V 4 Indium gallium arsenide phosphide InGaAsP
III-V 4 Indium gallium arsenide antimonide InGaAsSb Use in thermophotovoltaics.
III-V 4 Indium arsenide antimonide phosphide InAsSbP Use in thermophotovoltaics.
III-V 4 Aluminium indium arsenide phosphide AlInAsP
III-V 4 Aluminium gallium arsenide nitride AlGaAsN
III-V 4 Indium gallium arsenide nitride InGaAsN
III-V 4 Indium aluminium arsenide nitride InAlAsN
III-V 4 Gallium arsenide antimonide nitride GaAsSbN
III-V 5 Gallium indium nitride arsenide antimonide GaInNAsSb
III-V 5 Gallium indium arsenide antimonide phosphide GaInAsSbP Can be grown on InAs, GaSb, and other substrates. Can be lattice matched by varying composition. Possibly usable for mid-infrared LEDs.
II-VI 3 Cadmium zinc telluride, CZT CdZnTe 1.4 2.2 direct Efficient solid-state x-ray and gamma-ray detector, can operate at room temperature. High electro-optic coefficient. Used in solar cells. Can be used to generate and detect terahertz radiation. Can be used as a substrate for epitaxial growth of HgCdTe.
II-VI 3 Mercury cadmium telluride HgCdTe 0 1.5 Known as "MerCad". Extensive use in sensitive cooled infrared imaging sensors, infrared astronomy, and infrared detectors. Alloy of mercury telluride (a semimetal, zero band gap) and CdTe. High electron mobility. The only common material capable of operating in both 3–5 μm and 12–15 μm atmospheric windows. Can be grown on CdZnTe.
II-VI 3 Mercury zinc telluride HgZnTe 0 2.25 Used in infrared detectors, infrared imaging sensors, and infrared astronomy. Better mechanical and thermal properties than HgCdTe but more difficult to control the composition. More difficult to form complex heterostructures.
II-VI 3 Mercury zinc selenide HgZnSe
II-V 4 Zinc cadmium phosphide arsenide (Zn1−xCdx)3(P1−yAsy)2[51] 0[26] 1.5[52] Various applications in optoelectronics (incl. photovoltaics), electronics and thermoelectrics.[53]
other 4 Copper indium gallium selenide, CIGS Cu(In,Ga)Se2 1 1.7 direct CuInxGa1–xSe2. Polycrystalline. Used in thin film solar cells.

See also

edit

References

edit
  1. ^ Jones, E.D. (1991). "Control of Semiconductor Conductivity by Doping". In Miller, L. S.; Mullin, J. B. (eds.). Electronic Materials. New York: Plenum Press. pp. 155–171. doi:10.1007/978-1-4615-3818-9_12. ISBN 978-1-4613-6703-1.
  2. ^ Milton Ohring Reliability and failure of electronic materials and devices Academic Press, 1998, ISBN 0-12-524985-3, p. 310.
  3. ^ a b c d John Dakin, Robert G. W. Brown Handbook of optoelectronics, Volume 1, CRC Press, 2006 ISBN 0-7503-0646-7 p. 57
  4. ^ Yu, Peter; Cardona, Manuel (2010). Fundamentals of Semiconductors (4 ed.). Springer-Verlag Berlin Heidelberg. p. 2. Bibcode:2010fuse.book.....Y. doi:10.1007/978-3-642-00710-1. ISBN 978-3-642-00709-5.
  5. ^ a b c d e f g h i j k l m n o p q r s t u "NSM Archive - Physical Properties of Semiconductors". www.ioffe.ru. Archived from the original on 2015-09-28. Retrieved 2010-07-10.
  6. ^ a b c d e f g h i j k l m n o p q Safa O. Kasap; Peter Capper (2006). Springer handbook of electronic and photonic materials. Springer. pp. 54, 327. ISBN 978-0-387-26059-4.
  7. ^ Isberg, Jan; Hammersberg, Johan; Johansson, Erik; Wikström, Tobias; Twitchen, Daniel J.; Whitehead, Andrew J.; Coe, Steven E.; Scarsbrook, Geoffrey A. (2002-09-06). "High Carrier Mobility in Single-Crystal Plasma-Deposited Diamond". Science. 297 (5587): 1670–1672. Bibcode:2002Sci...297.1670I. doi:10.1126/science.1074374. ISSN 0036-8075. PMID 12215638. S2CID 27736134.
  8. ^ Pierre, Volpe (2010). "High breakdown voltage Schottky diodes synthesized on p-type CVD diamond layer". Physica Status Solidi. 207 (9): 2088–2092. Bibcode:2010PSSAR.207.2088V. doi:10.1002/pssa.201000055. S2CID 122210971.
  9. ^ Y. Tao, J. M. Boss, B. A. Moores, C. L. Degen (2012). Single-Crystal Diamond Nanomechanical Resonators with Quality Factors exceeding one Million. arXiv:1212.1347
  10. ^ S.H. Groves, C.R. Pidgeon, A.W. Ewald, R.J. Wagner Journal of Physics and Chemistry of Solids, Volume 31, Issue 9, September 1970, Pages 2031-2049 (1970). Interband magnetoreflection of α-Sn.
  11. ^ "Tin, Sn". www.matweb.com.
  12. ^ Abass, A. K.; Ahmad, N. H. (1986). "Indirect band gap investigation of orthorhombic single crystals of sulfur". Journal of Physics and Chemistry of Solids. 47 (2): 143. Bibcode:1986JPCS...47..143A. doi:10.1016/0022-3697(86)90123-X.
  13. ^ Nielsen, Rasmus; Youngman, Tomas H.; Moustafa, Hadeel; Levcenco, Sergiu; Hempel, Hannes; Crovetto, Andrea; Olsen, Thomas; Hansen, Ole; Chorkendorff, Ib; Unold, Thomas; Vesborg, Peter C. K. (2022). "Origin of photovoltaic losses in selenium solar cells with open-circuit voltages approaching 1 V". Journal of Materials Chemistry A. 10 (45): 24199–24207. doi:10.1039/D2TA07729A.
  14. ^ Todorov, T. (2017). "Ultrathin high band gap solar cells with improved efficiencies from the world's oldest photovoltaic material". Nature Communications. 8 (1): 682. Bibcode:2017NatCo...8..682T. doi:10.1038/s41467-017-00582-9. PMC 5613033. PMID 28947765. S2CID 256640449.
  15. ^ Nielsen, Rasmus; Crovetto, Andrea; Assar, Alireza; Hansen, Ole; Chorkendorff, Ib; Vesborg, Peter C.K. (12 March 2024). "Monolithic Selenium/Silicon Tandem Solar Cells". PRX Energy. 3 (1): 013013. arXiv:2307.05996. Bibcode:2024PRXE....3a3013N. doi:10.1103/PRXEnergy.3.013013.
  16. ^ Rajalakshmi, M.; Arora, Akhilesh (2001). "Stability of Monoclinic Selenium Nanoparticles". Solid State Physics. 44: 109.
  17. ^ a b Dorf, Richard (1993). The Electrical Engineering Handbook. CRC Press. pp. 2235–2236. ISBN 0-8493-0185-8.
  18. ^ a b Evans, D. A.; McGlynn, A. G.; Towlson, B. M.; Gunn, M.; Jones, D.; Jenkins, T. E.; Winter, R.; Poolton, N. R. J (2008). "Determination of the optical band-gap energy of cubic and hexagonal boron nitride using luminescence excitation spectroscopy" (PDF). Journal of Physics: Condensed Matter. 20 (7): 075233. Bibcode:2008JPCM...20g5233E. doi:10.1088/0953-8984/20/7/075233. hdl:2160/612. S2CID 52027854.
  19. ^ "Boron nitride nanotube". www.matweb.com.
  20. ^ a b c d Madelung, O. (2004). Semiconductors: Data Handbook. Birkhäuser. p. 1. ISBN 978-3-540-40488-0.
  21. ^ Claus F. Klingshirn (1997). Semiconductor optics. Springer. p. 127. ISBN 978-3-540-61687-0.
  22. ^ "Lead(II) sulfide". www.matweb.com.
  23. ^ Patel, Malkeshkumar; Indrajit Mukhopadhyay; Abhijit Ray (26 May 2013). "Annealing influence over structural and optical properties of sprayed SnS thin films". Optical Materials. 35 (9): 1693–1699. Bibcode:2013OptMa..35.1693P. doi:10.1016/j.optmat.2013.04.034.
  24. ^ Burton, Lee A.; Whittles, Thomas J.; Hesp, David; Linhart, Wojciech M.; Skelton, Jonathan M.; Hou, Bo; Webster, Richard F.; O'Dowd, Graeme; Reece, Christian; Cherns, David; Fermin, David J.; Veal, Tim D.; Dhanak, Vin R.; Walsh, Aron (2016). "Electronic and optical properties of single crystal SnS2: An earth-abundant disulfide photocatalyst". Journal of Materials Chemistry A. 4 (4): 1312–1318. doi:10.1039/C5TA08214E. hdl:10044/1/41359.
  25. ^ Haacke, G.; Castellion, G. A. (1964). "Preparation and Semiconducting Properties of Cd3P2". Journal of Applied Physics. 35 (8): 2484–2487. Bibcode:1964JAP....35.2484H. doi:10.1063/1.1702886.
  26. ^ a b Borisenko, Sergey; et al. (2014). "Experimental Realization of a Three-Dimensional Dirac Semimetal". Physical Review Letters. 113 (27603): 027603. arXiv:1309.7978. Bibcode:2014PhRvL.113b7603B. doi:10.1103/PhysRevLett.113.027603. PMID 25062235. S2CID 19882802.
  27. ^ Kimball, Gregory M.; Müller, Astrid M.; Lewis, Nathan S.; Atwater, Harry A. (2009). "Photoluminescence-based measurements of the energy gap and diffusion length of Zn3P2" (PDF). Applied Physics Letters. 95 (11): 112103. Bibcode:2009ApPhL..95k2103K. doi:10.1063/1.3225151. ISSN 0003-6951.
  28. ^ Syrbu, N. N.; Stamov, I. G.; Morozova, V. I.; Kiossev, V. K.; Peev, L. G. (1980). "Energy band structure of Zn3P2, ZnP2 and CdP2 crystals on wavelength modulated photoconductivity and photoresponnse spectra of Schottky diodes investigation". Proceedings of the First International Symposium on the Physics and Chemistry of II-V Compounds: 237–242.
  29. ^ a b Botha, J. R.; Scriven, G. J.; Engelbrecht, J. A. A.; Leitch, A. W. R. (1999). "Photoluminescence properties of metalorganic vapor phase epitaxial Zn3As2". Journal of Applied Physics. 86 (10): 5614–5618. Bibcode:1999JAP....86.5614B. doi:10.1063/1.371569.
  30. ^ a b c Rahimi, N.; Pax, R. A.; MacA. Gray, E. (2016). "Review of functional titanium oxides. I: TiO2 and its modifications". Progress in Solid State Chemistry. 44 (3): 86–105. doi:10.1016/j.progsolidstchem.2016.07.002.
  31. ^ S. Banerjee; et al. (2006). "Physics and chemistry of photocatalytic titanium dioxide: Visualization of bactericidal activity using atomic force microscopy" (PDF). Current Science. 90 (10): 1378.
  32. ^ O. Madelung; U. Rössler; M. Schulz, eds. (1998). "Cuprous oxide (Cu2O) band structure, band energies". Landolt-Börnstein – Group III Condensed Matter. Numerical Data and Functional Relationships in Science and Technology. Landolt-Börnstein - Group III Condensed Matter. Vol. 41C: Non-Tetrahedrally Bonded Elements and Binary Compounds I. pp. 1–4. doi:10.1007/10681727_62. ISBN 978-3-540-64583-2.
  33. ^ Lee, Thomas H. (2004). Planar Microwave Engineering: A practical guide to theory, measurement, and circuits. UK: Cambridge Univ. Press. p. 300. ISBN 978-0-521-83526-8.
  34. ^ Shin, S.; Suga, S.; Taniguchi, M.; Fujisawa, M.; Kanzaki, H.; Fujimori, A.; Daimon, H.; Ueda, Y.; Kosuge, K. (1990). "Vacuum-ultraviolet reflectance and photoemission study of the metal-insulator phase transitions in VO2, V6O13, and V2O3". Physical Review B. 41 (8): 4993–5009. Bibcode:1990PhRvB..41.4993S. doi:10.1103/physrevb.41.4993. PMID 9994356.
  35. ^ Sinha, Sapna (2020). "Atomic structure and defect dynamics of monolayer lead iodide nanodisks with epitaxial alignment on graphene". Nature Communications. 11 (1): 823. Bibcode:2020NatCo..11..823S. doi:10.1038/s41467-020-14481-z. PMC 7010709. PMID 32041958. S2CID 256633781.
  36. ^ Kobayashi, K.; Yamauchi, J. (1995). "Electronic structure and scanning-tunneling-microscopy image of molybdenum dichalcogenide surfaces". Physical Review B. 51 (23): 17085–17095. Bibcode:1995PhRvB..5117085K. doi:10.1103/PhysRevB.51.17085. PMID 9978722.
  37. ^ a b Arora, Himani; Erbe, Artur (2021). "Recent progress in contact, mobility, and encapsulation engineering of InSe and GaSe". InfoMat. 3 (6): 662–693. doi:10.1002/inf2.12160. ISSN 2567-3165.
  38. ^ a b Arora, Himani; Jung, Younghun; Venanzi, Tommaso; Watanabe, Kenji; Taniguchi, Takashi; Hübner, René; Schneider, Harald; Helm, Manfred; Hone, James C.; Erbe, Artur (2019-11-20). "Effective Hexagonal Boron Nitride Passivation of Few-Layered InSe and GaSe to Enhance Their Electronic and Optical Properties". ACS Applied Materials & Interfaces. 11 (46): 43480–43487. doi:10.1021/acsami.9b13442. hdl:11573/1555190. ISSN 1944-8244. PMID 31651146. S2CID 204884014.
  39. ^ a b c Arora, Himani (2020). "Charge transport in two-dimensional materials and their electronic applications" (PDF). Doctoral Dissertation. Retrieved July 1, 2021.
  40. ^ B. G. Yacobi Semiconductor materials: an introduction to basic principles Springer, 2003, ISBN 0-306-47361-5
  41. ^ Kumar, Manish; Sharma, Anjna; Maurya, Indresh Kumar; Thakur, Alpana; Kumar, Sunil (2019). "Synthesis of ultra small iron oxide and doped iron oxide nanostructures and their antimicrobial activities". Journal of Taibah University for Science. 13 (1): 280–285. Bibcode:2019JTUS...13..280K. doi:10.1080/16583655.2019.1565437. S2CID 139826266.
  42. ^ Synthesis and Characterization of Nano-Dimensional Nickelous Oxide (NiO) Semiconductor S. Chakrabarty and K. Chatterjee
  43. ^ Synthesis and Room Temperature Magnetic Behavior of Nickel Oxide Nanocrystallites Kwanruthai Wongsaprom*[a] and Santi Maensiri [b]
  44. ^ Arsenic sulfide (As2S3)
  45. ^ Temperature Dependence of Spectroscopic Performance of Thallium Bromide X- and Gamma-Ray Detectors
  46. ^ Hodes; Ebooks Corporation (8 October 2002). Chemical Solution Deposition of Semiconductor Films. CRC Press. pp. 319–. ISBN 978-0-8247-4345-1. Retrieved 28 June 2011.
  47. ^ Arumona Edward Arumona; Amah A. N. (2018). "Density Functional Theory Calculation of Band Gap of Iron (II) disulfide and Tellurium". Advanced Journal of Graduate Research. 3: 41–46. doi:10.21467/ajgr.3.1.41-46.
  48. ^ Prashant K Sarswat; Michael L Free (2013). "Enhanced Photoelectrochemical Response from Copper Antimony Zinc Sulfide Thin Films on Transparent Conducting Electrode". International Journal of Photoenergy. 2013: 1–7. doi:10.1155/2013/154694.
  49. ^ Yasantha Rajakarunanayake(1991) Optical properties of Si-Ge superlattices and wide band gap II-VI superlattices Dissertation (Ph.D.), California Institute of Technology
  50. ^ Hussain, Aftab M.; Fahad, Hossain M.; Singh, Nirpendra; Sevilla, Galo A. Torres; Schwingenschlögl, Udo; Hussain, Muhammad M. (2014). "Tin – an unlikely ally for silicon field effect transistors?". Physica Status Solidi RRL. 8 (4): 332–335. Bibcode:2014PSSRR...8..332H. doi:10.1002/pssr.201308300. S2CID 93729786.
  51. ^ Trukhan, V. M.; Izotov, A. D.; Shoukavaya, T. V. (2014). "Compounds and solid solutions of the Zn-Cd-P-As system in semiconductor electronics". Inorganic Materials. 50 (9): 868–873. doi:10.1134/S0020168514090143. S2CID 94409384.
  52. ^ Cisowski, J. (1982). "Level Ordering in II3-V2 Semiconducting Compounds". Physica Status Solidi B. 111 (1): 289–293. Bibcode:1982PSSBR.111..289C. doi:10.1002/pssb.2221110132.
  53. ^ Arushanov, E. K. (1992). "II3V2 compounds and alloys". Progress in Crystal Growth and Characterization of Materials. 25 (3): 131–201. doi:10.1016/0960-8974(92)90030-T.