The AVE Mizar (named after the star Mizar) was a roadable aircraft built between 1971 and 1973 by Advanced Vehicle Engineers (AVE) of Van Nuys, Los Angeles, California. The company was started by Henry Smolinski and Harold Blake, both graduates of Northrop Institute of Technology's aeronautical engineering school.[1]
AVE Mizar | |
---|---|
![]() | |
A Mizar at Oxnard Airport, Oxnard, California, August 1973 | |
Role | Roadable aircraft |
National origin | United States |
Manufacturer | Advanced Vehicle Engineers |
Designer | Henry Smolinski |
Introduction | 1973 |
Number built | 2 |
Developed from | Ford Pinto, Cessna Skymaster |
Development
editPrototypes
editThe prototypes of the Mizar were made by mating the rear portion of a Cessna Skymaster to a Ford Pinto.[2] The pod-and-twin-boom configuration of the Skymaster was a convenient starting point for a hybrid automobile/airplane. The passenger space and front engine of the Skymaster were removed, leaving an airframe ready to attach to a small car. AVE planned to have its own airframe purpose-built by a subcontractor for production models, rather than depending on Cessna for airframes.[3]
By mid-1973, two prototypes had been built and three more were under construction. One prototype was slated for static display at a Van Nuys Ford dealership, owned by AVE partner Bert Boeckmann. The other prototype, fitted with a Teledyne Continental Motors 210 horsepower (160 kW) engine, was unveiled to the press on May 8, 1973. Both vehicles were photographed by Petersen Publishing photographer Mike Brenner for Hot Rod magazine in late April. It then began a series of taxi tests at Van Nuys Airport. AVE made special arrangements to do flight testing at the U.S. Navy's test facilities at Naval Air Station Point Mugu, California. AVE stated that Federal Aviation Administration certification flights were underway in mid-1973.[4][page needed][5]
The Mizar was intended to use both the aircraft engine and the car engine for takeoff. This would considerably shorten the takeoff roll. Once in the air, the car engine would be turned off. Upon landing, the four-wheel braking would stop the craft in 525 ft (160 m) or less. On the ground, telescoping wing supports would be extended and the airframe would be tied down like any other aircraft. The Pinto could be quickly unbolted from the airframe and driven away.[5]
Production was scheduled to begin in 1974. AVE had stated that prices would range from US$18,300 to $29,000.[5]
Test flights
editOn a test flight from Camarillo Airport in California on August 26, 1973, according to test pilot Charles "Red" Janisse, the right wing strut base mounting attachment failed soon after takeoff. Because turning the aircraft would put too much stress on the unsupported wing, Janisse put the aircraft down in a bean field. After the roadway was closed to traffic, Janisse drove the otherwise undamaged aircraft back to the airport.
On September 11, 1973, during a test flight at Camarillo, the right wing strut again detached from the Pinto. With Janisse not available for this test flight, Mizar creator Smolinski was at the controls. Although some reports say the Pinto separated from the airframe, air traffic controller Reed Weske, who was watching through binoculars, said the aircraft disintegrated after taking off and making a right turn.[6] According to Janisse, the wing folded because the pilot tried to turn the aircraft when the wing strut support failed. Smolinski and the Vice President of AVE, Harold Blake, were killed in the resulting crash.[6][7]
Analysis
editEven though the Pinto was a light car, the total aircraft without passengers or fuel was already slightly over the certified gross weight of a Skymaster. However, in addition to poor aircraft design and loose parts, the National Transportation Safety Board reported that bad welds were partly responsible for the crash, with the right wing strut attachment failing at a body panel of the Pinto.[8][9]
Specifications
editData from Special Use Vehicles: An Illustrated History of Unconventional Cars and Trucks Worldwide and Peterson's Complete Ford Book
General characteristics
- Crew: one, pilot
- Capacity: three passengers
- Length: 28 ft 0 in (8.5 m)
- Wingspan: 38 ft 0 in (11.58 m)
- Height: 8 ft 6 in (2.59 m)
- Wing area: 201 sq ft (18.7 m2)
- Powerplant: 1 × Continental IO-360-C , 210 hp (157 kW)
Performance
- Service ceiling: 12,000 ft (3,657.6 m)
See also
editRelated development
Aircraft of comparable role, configuration, and era
References
edit- ^ Brian Campbell (1973-09-11). "The History Of... AVE Mizar Flying Pinto". Cookieboystoys.com. Archived from the original on 2011-10-03. Retrieved 2013-06-07.
- ^ "Flying Pinto Sprouts Wings". Popular Mechanics. September 1973.
- ^ George W. Green (2003). Special Use Vehicles: An Illustrated History of Unconventional Cars and Trucks Worldwide. McFarland. p. 185. ISBN 978-0-7864-2911-0.
- ^ Petersen, Petersen's Complete Ford Book 3rd Edition (1973)
- ^ a b c "Car That Can Fly Away Developed in Van Nuys". The Van Nuys News. May 15, 1973.
- ^ a b "Flying Automobile Crashes, Burns in Oxnard; 2 Killed". The Los Angeles Times. September 12, 1973. p. 3. Archived from the original on August 5, 2021. Retrieved August 5, 2021 – via Newspapers.com.
- ^ Soniak, Matt (July 30, 2012). "The Flying Pinto That Killed Its Inventor". Mental Floss. Retrieved August 5, 2021.
- ^ Accident report – NTSB Identification: LAX74FUQ18, National Transportation Safety Board
- ^ Garrison, Peter (August 1993). "Can We Ever Make A Car Airworthy?". Flying. Retrieved 2012-11-20.