NZASM 32 Tonner 0-4-2RT

(Redirected from NZASM 32 Tonner 0-4-2T)

The NZASM 32 Tonner 0-4-2RT of 1894 was a South African steam locomotive from the pre-Union era in Transvaal.

NZASM 32 Tonner 0-4-2RT
CSAR Class G 0-4-2RT
NZASM 32 Tonner rack locomotive no. 992, c. 1895
Type and origin
Power typeSteam
DesignerMaschinenfabrik Esslingen
BuilderMaschinenfabrik Esslingen
Serial numberEsslingen 2642, 2643, 2655 & 2844
ModelNZASM Rack
Build date1894–1897
Total produced4
Specifications
Configuration:
 • Whyte0-4-2RT (Olomana)
 • UICB1n2t
Driver2nd coupled axle
Gauge3 ft 6 in (1,067 mm) Cape gauge
Coupled dia.38+78 in (987 mm)
Trailing dia.31+78 in (810 mm)
Wheelbase14 ft 1+516 in (4,301 mm) ​
 • Coupled8 ft 1+716 in (2,475 mm)
Length:
 • Over couplers29 ft 6 in (8,992 mm)
Height12 ft 8+532 in (3,865 mm)
Frame typePlate
Axle load11 LT 7 cwt (11,530 kg) ​
 • 1st coupled11 LT 6 cwt (11,480 kg)
 • 2nd coupled11 LT 7 cwt (11,530 kg)
 • Trailing7 LT 1 cwt (7,163 kg)
Adhesive weight22 LT 13 cwt (23,010 kg)
Loco weight29 LT 14 cwt (30,180 kg)
Fuel typeCoal
Fuel capacity1 LT (1.0 t)
Water cap.550 imp gal (2,500 L)
Firebox:
 • TypeRound-top
 • Grate area14.2 sq ft (1.32 m2)
Boiler:
 • Pitch6 ft 1+732 in (1,860 mm)
 • Diameter3 ft 8+14 in (1,124 mm)
 • Tube plates10 ft 6 in (3,200 mm)
 • Small tubes156: 1+2532 in (45 mm)
Boiler pressure180 psi (1,241 kPa)
Heating surface:
 • Firebox73 sq ft (6.8 m2)
 • Tubes760 sq ft (71 m2)
 • Total surface833 sq ft (77.4 m2)
CylindersTwo
Cylinder size18+2932 in (480 mm) bore
24+1316 in (630 mm) stroke
Valve gearHeusinger
Valve typeSlide
CouplersJohnston link-and-pin
Performance figures
Tractive effort27,154 lbf (120.79 kN) @ 75%
Career
OperatorsNZASM
Imperial Military Railways
Central South African Railways
South African Railways
ClassNZASM 32 Tonner
CSAR Class G
Number in class4
Numbers991–994
Official nameSee table
Delivered1894–1897
First run1894

In 1894 and 1897, the Nederlandsche-Zuid-Afrikaansche Spoorweg-Maatschappij of the Zuid-Afrikaansche Republiek (Transvaal Republic) placed four rack tank locomotives with a 0-4-2 wheel arrangement in service on the rack section between Waterval Onder and Waterval Boven. Since the railway classified its locomotives according to their weight, these engines were known as the 32 Tonners.[1][2]

Waterval Onder to Waterval Boven

edit

The construction of the railway line from Delagoa Bay to Pretoria was beset with difficulties, both in terms of disease and engineering. Malaria claimed many lives among the construction crews and some of the terrain was mountainous. In the Elandspruit valley, where the Elands River formed a 295-foot high (90-metre) waterfall, the adjacent cliffs presented a natural barrier to the continuation of the railway from the Eastern Transvaal Lowveld up to the Transvaal Highveld.[1][2]

In terms of construction, the climb up the escarpment was arguably the most difficult section on the route to be encountered by the railway builders. When the line reached Waterval Onder, they had a choice between a lengthy detour with sharp curves and costly deep cuttings, embankments and viaducts to comply with the agreed upon gradient of 1 in 50 (2%), or a shorter 4+12-mile long (7.2-kilometre) section, which would entail a gradient of 1 in 20 (5%) over a distance of 2.1 miles (3.4 kilometres) in one place, as well as a 233-yard long (213-metre) tunnel.[1][2]

The shorter and steeper route was selected. While a gradient of 1 in 20 (5%) is not insurmountable by light trains with orthodox adhesion locomotives, safety and economical considerations led to the decision to install a rack track on the steep section up the escarpment between Waterval Onder and Waterval Boven. The rack track was built to the Riggenbach system which was in use on European mountain railways, with the rack laid between the rails.[1][2]

 
Riggenbach rack system

The Riggenbach rack system used a ladder rack, formed of steel channels connected by square rungs at regular intervals, to engage the pinion wheels of the rack engine. The rungs of the NZASM rack track were spaced 4 inches (102 millimetres) apart. To ensure correct meshing of the gears when entering the rack section, engaging pieces of special section, 6 feet 6+34 inches (2,000 millimetres) long and fitted with round-bar rungs, were hinged to each end of the rack, supported by a spiral spring underneath. When the rack engine made contact with the hinged section and the gear wheels did not mesh with the rack correctly, the engaging section would be pressed down until correct meshing was accomplished.[2][3]

Manufacturer

edit

The line from Delagoa Bay and up the escarpment to Waterval Boven was completed on 20 June 1894. To work on the rack section, the Nederlandsche-Zuid-Afrikaansche Spoorweg-Maatschappij (NZASM) ordered three 0-4-2 rack tank locomotives from Emil Kessler's Maschinenfabrik Esslingen. The three locomotives were delivered in 1894, numbered in the range from 991 to 993. A fourth locomotive, no. 994, was ordered in 1897 and was identical to the other three, except that it had a coal bunker and water tanks with larger capacities, which made it heavier. Since the NZASM classified its locomotives according to their weight, the rack locomotives were known as 32 Tonners. In addition to being numbered, they were all named as well, with the names and numbers cast in brass and mounted on their tank sides.[1][2][4][5]

Characteristics

edit

The rack locomotive had plate frames, arranged outside the coupled wheels, and was equipped with the Heusinger von Waldegg version of Walschaerts valve gear. The pinion for the rack was mounted between the coupled wheels, just forward of the driving axle. The pinion axle was coupled to the drivers through side rods, with the connecting rods coupled directly to crank disks which were mounted on the ends of the axle, outside the frames. These crank disks were grooved to act as brake drums.[1][2]

A second free-turning pinion wheel which also meshed with the rack, was mounted on the leading driving axle. It had grooved brake drums bolted to each side and acted as a brake only, with the brakes being applied by a hand mechanism from the footplate. The brakes on the driving and free-turning pinion wheels were separately controlled, while the vacuum brake gear on the engine was only used to control the brakes of the train.[2]

The main steam cylinders were also used as brakes on the rack section. During descents, the 32 Tonner would be put into reverse with the steam regulator closed and a three-way valve in the exhaust pipe under the smokebox would be closed when brake power was required. The exhaust passages would then be isolated from the blast pipe and air would be admitted to the steam chests. The air would enter the cylinders though the exhaust ports and therefore reversed operations in the cylinders. Used air would be exhausted through the steam inlet ports back into the steam pipe, from where it was led to the rear of the engine by a 1+12-inch diameter (38-millimetre) branch pipe. This branch pipe had another valve, by which the driver could regulate the amount of compression in the cylinders. Small amounts of water could be admitted into the cylinders to keep them cool.[1][2]

Service

edit

NZASM

edit

The four rack locomotives were all shedded at Waterval Onder. When working a train up to Waterval Boven, a 32 Tonner would be coupled to the rear end of a train as banking engine. When working a descending train, the order of assembly was reversed, with the train's locomotive at the rear end and the rack locomotive in front to act as brake. Loads of 120 to 140 long tons (122 to 142 tonnes) could be handled in this manner.[1][2]

Imperial Military Railways

edit

All railway operations in the two Boer Republics, the Zuid-Afrikaansche Republiek and the Orange Free State, were taken over by the Imperial Military Railways (IMR) in 1899, during the Second Boer War.[4]

All four locomotives survived the war.[5]

Central South African Railways

edit

At the end of the war in 1902, when the IMR was transformed into the Central South African Railways (CSAR), the four 32 Tonners were designated Class G, but retained their original NZASM engine numbers. They remained in banking service on the section between Waterval Boven and Waterval Onder until 1908, when a new alignment with easier gradients, including a new tunnel, was constructed and the rack section could be abandoned.[1][2]

The original tunnel's portal coordinates are 25°38′17″S 30°20′48″E / 25.638170°S 30.346637°E / -25.638170; 30.346637 (southeastern portal) and 25°38′11″S 30°20′43″E / 25.636465°S 30.345353°E / -25.636465; 30.345353 (northwestern portal). The new 1908 tunnel's portal coordinates are 25°38′01″S 30°20′57″E / 25.633522°S 30.349168°E / -25.633522; 30.349168 (eastern portal) and 25°38′04″S 30°20′42″E / 25.634496°S 30.345066°E / -25.634496; 30.345066 (western portal).

South African Railways

edit

When the Union of South Africa was established on 31 May 1910, the three Colonial government railways (Cape Government Railways, Natal Government Railways and CSAR) were united under a single administration to control and administer the railways, ports and harbours of the Union. Although the South African Railways and Harbours came into existence in 1910, the actual classification and renumbering of all the rolling stock of the three constituent railways was only implemented with effect from 1 January 1912.[4][6]

In 1912, these four locomotives were taken onto the SAR roster as unclassified engines, since they were considered obsolete. Since they were excluded from the SAR renumbering schedules, they retained their NZASM engine numbers until they were eventually scrapped.[5][6]

Names and works numbers

edit

The 32 Tonner engine numbers, names, works numbers and years built are listed in the table.[1]

Illustration

edit

The main picture shows no. 992 Driekleur while the following pictures serve to illustrate the larger coal bunker on the fourth engine.

References

edit
  1. ^ a b c d e f g h i j Holland, D.F. (1971). Steam Locomotives of the South African Railways. Vol. 1: 1859–1910 (1st ed.). Newton Abbott, England: David & Charles. pp. 115–117, 126. ISBN 978-0-7153-5382-0.
  2. ^ a b c d e f g h i j k Espitalier, T.J.; Day, W.A.J. (1944). The Locomotive in South Africa – A Brief History of Railway Development. Chapter IV – The N.Z.A.S.M. (Continued). South African Railways and Harbours Magazine, November 1944. pp. 843–845, 848.
  3. ^ Jehan, David (2003). Rack Railways of Australia (2nd. ed.). Illawarra Light Railway Museum Society. ISBN 0-9750452-0-2.
  4. ^ a b c The South African Railways – Historical Survey. Editor George Hart, Publisher Bill Hart, Sponsored by Dorbyl Ltd., Published c. 1978, pp. 19–20, 22–23, 25.
  5. ^ a b c Paxton, Leith; Bourne, David (1985). Locomotives of the South African Railways (1st ed.). Cape Town: Struik. p. 23. ISBN 0869772112.
  6. ^ a b Classification of S.A.R. Engines with Renumbering Lists, issued by the Chief Mechanical Engineer's Office, Pretoria, January 1912, p. 2 (Reprinted in April 1987 by SATS Museum, R.3125-6/9/11-1000)