Phase-shift mask

(Redirected from Phase-shifting mask)

Phase-shift masks are photomasks that take advantage of the interference generated by phase differences to improve image resolution in photolithography. There exist alternating[1] and attenuated phase shift masks.[2] A phase-shift mask relies on the fact that light passing through a transparent media will undergo a phase change as a function of its optical thickness.

A schematic illustration of various types of masks: (a) a conventional (binary) mask; (b) an alternating phase-shift mask; (c) an attenuated phase-shift mask.
Left: the real part of a plane wave traveling downward. Right: the effect of introducing in the path of the wave a transparent mask with a 180° phase-shifting region. (The illustration on the right ignores the effect of diffraction which increases in significance as the wave propagates.)
Phase-Shift Mask Types: (1) Binary mask, (2) Phase Shift mask, (3) Etched Quartz mask (Levenson mask), (4) Half-tone mask. (Top) Mask, (Red) Light Energy/Phase on Mask, (Blue) Light Energy/Phase on Wafer, (Green) Light Power on Wafer, (Bottom) Resist on Silicon Wafer

Types and effects

edit

A conventional photomask is a transparent plate with the same thickness everywhere, parts of which are covered with non-transmitting material in order to create a pattern on the semiconductor wafer when illuminated.

In alternating phase-shift masks, certain transmitting regions are made thinner or thicker. That induces a phase-shift in the light traveling through those regions of the mask (see the illustration). When the thickness is suitably chosen, the interference of the phase-shifted light with the light coming from unmodified regions of the mask has the effect of improving the contrast on some parts of the wafer, which may ultimately increase the resolution on the wafer. The ideal case is a phase shift of 180 degrees, which results in all the incident light being scattered. However, even for smaller phase shifts, the amount of scattering is not negligible. It can be shown that only for phase shifts of 37 degrees or less will a phase edge scatter 10% or less of the incident light.

 
Plot of scattered light (normalized to incident light) as a function of the phase of a phase edge.

Attenuated phase-shift masks employ a different approach. Certain light-blocking parts of the mask are modified to allow a small amount of light to be transmitted through (typically just a few percent). That light is not strong enough to create a pattern on the wafer, but it can interfere with the light coming from the transparent parts of the mask, with the goal again of improving the contrast on the wafer.

Attenuated phase-shift masks are already extensively used, due to their simpler construction and operation, particularly in combination with optimized illumination for memory patterns. On the other hand, alternating phase-shift masks are more difficult to manufacture and this has slowed their adoption, but their use is becoming more widespread. For example, the alternating phase-shift mask technique is being used by Intel to print gates for their 65 nm and subsequent node transistors.[3][4] While alternating phase-shift masks are a stronger form of resolution enhancement than attenuated phase-shift masks, their use has more complex consequences. For example, a 180 degree phase edge or boundary will generally print. This printed edge is usually an unwanted feature and is usually removed by a second exposure.

Application

edit

A benefit of using phase-shift masks in lithography is the reduced sensitivity to variations of feature sizes on the mask itself. This is most commonly used in alternating phase-shift masks, where the linewidth becomes less and less sensitive to the chrome width on the mask, as the chrome width decreases. In fact, even with no chrome the phase edge can still print, as noted above. Some cases of attenuated phase-shifting masks also demonstrate the same benefit (see figure). Attenuated phase-shift masks also improve the image log-slope without requiring a very high exposure dose with a widened dark feature.[5] A higher transmission enhances the effect.[6]

As phase-shift masks are applied to printing smaller and smaller features, it becomes more and more important to model them accurately using rigorous simulation software, such as Panoramic Technology or Sigma-C. It becomes especially important as the mask topography starts to play an important role in scattering the light, and the light itself starts to propagate at larger angles. The performance of phase-shift masks can also be previewed with the use of aerial image microscopes. Defect inspection remains a critical aspect of phase-shift mask technology, as the set of printable mask defects has expanded to include those with phase effects in addition to conventional transmission effects.

Attenuated phase shift masks have been in use in production since the 90 nm node.[7]

References

edit
  1. ^ "Alternating phase shift masks at FreePatentsOnline".
  2. ^ "Attenuated phase shift masks at FreePatentsOnline".
  3. ^ A. Tritchkov, S. Jeong, and C. Kenyon, "Lithography Enabling for the 65 nm node gate layer patterning with Alternating PSM," Proc. SPIE vol. 5754, pp.215-225 (2005).
  4. ^ S. Perlitz et al., "Novel solution for in-die phase control under scanner equivalent optical settings for 45-nm node and below," Proc. SPIE vol. 6607 (2007).
  5. ^ Phase-Shifting Masks - A Handicap for EUV?
  6. ^ NILS Enhancement with Higher Transmission Phase-Shift Masks
  7. ^ C-H. Chang et al., Proc. SPIE 5377, 902 (2004).

Further reading

edit
  • Levinson, Harry (2004). Principles of Lithography (2nd ed.). SPIE—The International Society for Optical Engineering. ISBN 0-8194-5660-8.
  • Rai-Choudhury, P., editor (1997). Handbook of Microlithography, Micromachining, and Microfabrication. Volume 1: Microlithography. Bellingham, Washington: SPIE Optical Engineering Press. ISBN 0-85296-906-6. {{cite book}}: |author= has generic name (help)CS1 maint: multiple names: authors list (link)