Luminance is a photometric measure of the luminous intensity per unit area of light travelling in a given direction.[1] It describes the amount of light that passes through, is emitted from, or is reflected from a particular area, and falls within a given solid angle.

A tea light-type candle, imaged with a luminance camera; false colors indicate luminance levels per the bar on the right (cd/m2)

The procedure for conversion from spectral radiance to luminance is standardized by the CIE and ISO.[2]

Brightness is the term for the subjective impression of the objective luminance measurement standard (see Objectivity (science) § Objectivity in measurement for the importance of this contrast).

The SI unit for luminance is candela per square metre (cd/m2). A non-SI term for the same unit is the nit. The unit in the Centimetre–gram–second system of units (CGS) (which predated the SI system) is the stilb, which is equal to one candela per square centimetre or 10 kcd/m2.

Description

edit

Luminance is often used to characterize emission or reflection from flat, diffuse surfaces. Luminance levels indicate how much luminous power could be detected by the human eye looking at a particular surface from a particular angle of view. Luminance is thus an indicator of how bright the surface will appear. In this case, the solid angle of interest is the solid angle subtended by the eye's pupil.

Luminance is used in the video industry to characterize the brightness of displays. A typical computer display emits between 50 and 300 cd/m2. The sun has a luminance of about 1.6×109 cd/m2 at noon.[3]

Luminance is invariant in geometric optics.[4] This means that for an ideal optical system, the luminance at the output is the same as the input luminance.

For real, passive optical systems, the output luminance is at most equal to the input. As an example, if one uses a lens to form an image that is smaller than the source object, the luminous power is concentrated into a smaller area, meaning that the illuminance is higher at the image. The light at the image plane, however, fills a larger solid angle so the luminance comes out to be the same assuming there is no loss at the lens. The image can never be "brighter" than the source.

Health effects

edit

Retinal damage can occur when the eye is exposed to high luminance. Damage can occur because of local heating of the retina. Photochemical effects can also cause damage, especially at short wavelengths.[5]

The IEC 60825 series gives guidance on safety relating to exposure of the eye to lasers, which are high luminance sources. The IEC 62471 series gives guidance for evaluating the photobiological safety of lamps and lamp systems including luminaires. Specifically it specifies the exposure limits, reference measurement technique and classification scheme for the evaluation and control of photobiological hazards from all electrically powered incoherent broadband sources of optical radiation, including LEDs but excluding lasers, in the wavelength range from 200 nm through 3000 nm. This standard was prepared as Standard CIE S 009:2002 by the International Commission on Illumination.

Luminance meter

edit

A luminance meter is a device used in photometry that can measure the luminance in a particular direction and with a particular solid angle. The simplest devices measure the luminance in a single direction while imaging luminance meters measure luminance in a way similar to the way a digital camera records color images.[6]

Formulation

edit
 
Parameters for defining the luminance

The luminance of a specified point of a light source, in a specified direction, is defined by the mixed partial derivative   where

  • Lv is the luminance (cd/m2);
  • d2Φv is the luminous flux (lm) leaving the area in any direction contained inside the solid angle Σ;
  • is an infinitesimal area (m2) of the source containing the specified point;
  • Σ is an infinitesimal solid angle (sr) containing the specified direction; and
  • θΣ is the angle between the normal nΣ to the surface and the specified direction.[7]

If light travels through a lossless medium, the luminance does not change along a given light ray. As the ray crosses an arbitrary surface S, the luminance is given by   where

  • dS is the infinitesimal area of S seen from the source inside the solid angle Σ;
  • S is the infinitesimal solid angle subtended by as seen from dS; and
  • θS is the angle between the normal nS to dS and the direction of the light.

More generally, the luminance along a light ray can be defined as   where

  • dG is the etendue of an infinitesimally narrow beam containing the specified ray;
  • v is the luminous flux carried by this beam; and
  • n is the index of refraction of the medium.

Relation to illuminance

edit
 
Comparison of photometric and radiometric quantities

The luminance of a reflecting surface is related to the illuminance it receives:   where the integral covers all the directions of emission ΩΣ,

In the case of a perfectly diffuse reflector (also called a Lambertian reflector), the luminance is isotropic, per Lambert's cosine law. Then the relationship is simply  

Units

edit

A variety of units have been used for luminance, besides the candela per square metre. Luminance is essentially the same as surface brightness, the term used in astronomy. This is measured with a logarithmic scale, magnitudes per square arcsecond (MPSAS).

Units of luminance
cd/m2 (SI unit)
≡ nit ≡ lm/m2/sr
stilb (sb) (CGS unit)
≡ cd/cm2
apostilb (asb)
≡ blondel
bril skot (sk) lambert (L) foot-lambert (fL)
= 1 ⁄ π cd/ft2
1 cd/m2 = 1 10−4 π
≈ 3.142
107 π
≈ 3.142×107
103 π
≈ 3.142×103
10−4 π
≈ 3.142×10−4
0.30482 π
≈ 0.2919
1 sb = 104 1 104 π
≈ 3.142×104
1011 π
≈ 3.142×1011
107 π
≈ 3.142×107
π
≈ 3.142
30.482 π
≈ 2919
1 asb = 1 ⁄ π
≈ 0.3183
10−4π
≈ 3.183×10−5
1 107 103 10−4 0.30482
≈ 0.09290
1 bril = 10−7π
≈ 3.183×10−8
10−11π
≈ 3.183×10−12
10−7 1 10−4 10−11 0.30482×10−7
≈ 9.290×10−9
1 sk = 10−3π
≈ 3.183×10−4
10−7π
≈ 3.183×10−8
10−3 104 1 10−7 0.30482×10−3
≈ 9.290×10−5
1 L = 104π
≈ 3183
1 ⁄ π
≈ 0.3183
104 1011 107 1 0.30482×104
≈ 929.0
1 fL = 1 ⁄ 0.30482π
≈ 3.426
1 ⁄ 30.482π
≈ 3.426×10−4
1 ⁄ 0.30482
≈ 10.76
107 ⁄ 0.30482
≈ 1.076×108
103 ⁄ 0.30482
≈ 1.076×104
10−4 ⁄ 0.30482
≈ 1.076×10−3
1

See also

edit
edit

Quantity Unit Dimension
[nb 1]
Notes
Name Symbol[nb 2] Name Symbol
Luminous energy Qv[nb 3] lumen second lm⋅s TJ The lumen second is sometimes called the talbot.
Luminous flux, luminous power Φv[nb 3] lumen (= candela steradian) lm (= cd⋅sr) J Luminous energy per unit time
Luminous intensity Iv candela (= lumen per steradian) cd (= lm/sr) J Luminous flux per unit solid angle
Luminance Lv candela per square metre cd/m2 (= lm/(sr⋅m2)) L−2J Luminous flux per unit solid angle per unit projected source area. The candela per square metre is sometimes called the nit.
Illuminance Ev lux (= lumen per square metre) lx (= lm/m2) L−2J Luminous flux incident on a surface
Luminous exitance, luminous emittance Mv lumen per square metre lm/m2 L−2J Luminous flux emitted from a surface
Luminous exposure Hv lux second lx⋅s L−2TJ Time-integrated illuminance
Luminous energy density ωv lumen second per cubic metre lm⋅s/m3 L−3TJ
Luminous efficacy (of radiation) K lumen per watt lm/W M−1L−2T3J Ratio of luminous flux to radiant flux
Luminous efficacy (of a source) η[nb 3] lumen per watt lm/W M−1L−2T3J Ratio of luminous flux to power consumption
Luminous efficiency, luminous coefficient V 1 Luminous efficacy normalized by the maximum possible efficacy
See also:
  1. ^ The symbols in this column denote dimensions; "L", "T" and "J" are for length, time and luminous intensity respectively, not the symbols for the units litre, tesla and joule.
  2. ^ Standards organizations recommend that photometric quantities be denoted with a subscript "v" (for "visual") to avoid confusion with radiometric or photon quantities. For example: USA Standard Letter Symbols for Illuminating Engineering USAS Z7.1-1967, Y10.18-1967
  3. ^ a b c Alternative symbols sometimes seen: W for luminous energy, P or F for luminous flux, and ρ for luminous efficacy of a source.

References

edit
  1. ^ "luminance, 17-21-050". CIE S 017:2020 ILV: International Lighting Vocabulary, 2nd edition. CIE - International Commission on Illumination. 2020. Retrieved 20 April 2023.
  2. ^ ISO/CIE 23539:2023 CIE TC 2-93 Photometry — The CIE system of physical photometry. ISO/CIE. 2023. doi:10.25039/IS0.CIE.23539.2023.
  3. ^ "Luminance". Lighting Design Glossary. Retrieved Apr 13, 2009.
  4. ^ Dörband, Bernd; Gross, Herbert; Müller, Henriette (2012). Gross, Herbert (ed.). Handbook of Optical Systems. Vol. 5, Metrology of Optical Components and Systems. Wiley. p. 326. ISBN 978-3-527-40381-3.
  5. ^ IEC 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements (in English, French, and Spanish) (3rd ed.). International Electrotechnical Commission. 2014-05-15. p. 220. - TC 76 - Optical radiation safety and laser equipment
  6. ^ "e-ILV : Luminance meter". CIE. Archived from the original on 16 September 2017. Retrieved 20 February 2013.
  7. ^ Chaves, Julio (2015). Introduction to Nonimaging Optics, Second Edition. CRC Press. p. 679. ISBN 978-1482206739. Archived from the original on 2016-02-18.
edit