A reference designator unambiguously identifies the location of a component within an electrical schematic or on a printed circuit board. The reference designator usually consists of one or two letters followed by a number, e.g. C3, D1, R4, U15. The number is sometimes followed by a letter, indicating that components are grouped or matched with each other, e.g. R17A, R17B. The IEEE 315 standard contains a list of Class Designation Letters to use for electrical and electronic assemblies. For example, the letter R is a reference prefix for the resistors of an assembly, C for capacitors, K for relays.
Industrial electrical installations often use reference designators according to IEC 81346.
History
editIEEE 200-1975 or "Standard Reference Designations for Electrical and Electronics Parts and Equipments" is a standard that was used to define referencing naming systems for collections of electronic equipment. IEEE 200 was ratified in 1975. The IEEE renewed the standard in the 1990s, but withdrew it from active support shortly thereafter. This document also has an ANSI document number, ANSI Y32.16-1975.
This standard codified information from, among other sources, a United States military standard MIL-STD-16 which dates back to at least the 1950s in American industry.
To replace IEEE 200-1975, ASME, a standards body for mechanical engineers, initiated the new standard ASME Y14.44-2008. This standard, along with IEEE 315-1975, provide the electrical designer with guidance on how to properly reference and annotate everything from a single circuit board to a collection of complete enclosures.
Definition
editASME Y14.44-2008[1] and IEEE 315-1975[2] define how to reference and annotate components of electronic devices.
It breaks down a system into units, and then any number of sub-assemblies. The unit is the highest level of demarcation in a system and is always a numeral. Subsequent demarcation are called assemblies and always have the Class Letter "A" as a prefix following by a sequential number starting with 1. Any number of sub-assemblies may be defined until finally reaching the component. Note that IEEE 315-1975[2] defines separate class designation letters for separable assemblies (class designation 'A') and inseparable assemblies (class designation 'U'). Inseparable assemblies—i.e., "items which are ordinarily replaced as a single item of supply"[2]—are typically treated as components in this referencing scheme.
Examples:
- 1A12A2R3 - Unit 1, Assembly 12, Sub-assembly 2, Resistor 3
- 1A12A2U3 - Unit 1, Assembly 12, Sub-assembly 2, Inseparable Assembly 3
Especially valuable is the method of referencing and annotating cables plus their connectors within and outside assemblies. Examples:
- 1A1A44J5 - Unit 1, Assembly 1, Sub-Assembly 44, Jack 5 (J5 is a connector on a box referenced as A44)
- 1A1A45J333 - Unit 1, Assembly 1, Sub-Assembly 45, Jack 333 (J333 is a connector on a box referenced as A45)
A cable connecting these two might be:
- 1A1W35 - In the assembly A1 is a cable called W35.
Connectors on this cable would be designated:
- 1A1W35P1
- 1A1W35P2
ASME Y14.44-2008 continues the convention of Plug P and Jack J when assigning references for electrical connectors in assemblies where a J (or jack) is the more fixed and P (or plug) is the less fixed of a connector pair, without regard to the gender of the connector contacts.
The construction of reference designators is covered by IEEE 200-1975/ANSI Y32.16-1975[3] (replaced by ASME Y14.44-2008[1]) and IEEE 315-1975.[2]
Designators
editThe table below lists designators commonly used, and does not necessarily comply with standards. For modern use, designators are often simplified towards shorter designators, because it requires less space on silkscreens.
| Designator | Component type | Modern use |
|---|---|---|
| A | Separable assembly or sub-assembly (e.g. printed circuit assembly) | |
| AT | Attenuator or isolator | |
| BR | Bridge rectifier (four diodes in a package) | often changed to "D" for diode |
| BT, BAT | Battery or battery holder | often shortened to "B" |
| C | Capacitor | |
| CB | Circuit breaker | |
| CN | Capacitor network | may be simplified to "C" for capacitor |
| D, CR | Diode (all types, including LED), thyristor | "D" is preferred for various types of diodes |
| DL | Delay line | |
| DN | Diode network | may be simplified to "D" for diode |
| DS | Display, general light source, lamp, signal light | |
| F | Fuse | |
| FB | Ferrite bead | sometimes changed to "L" for inductor, though "E" was used in the currently inactive standard IEEE 315 (see Clause 22.4). |
| FD | Fiducial | |
| FL | Filter | |
| G, OSC | Generator or oscillator | |
| GL | Graphical logo | |
| GN | General network | |
| H | Hardware, e.g., screws, nuts, washers, also used for drilled holes | sometimes hardware is expanded to "HW" |
| HY | Circulator or directional coupler | |
| IR | Infrared diode | often changed to "D" for diode |
| J | Jack (least-movable connector of a connector pair), jack connector (connector may have "male" pin contacts and/or "female" socket contacts) | all types of connectors, including pin headers. |
| JP | Jumper (link) | |
| K | Relay or contactor | |
| L | Inductor or coil or ferrite bead | |
| LD, LED | LED | often changed to "D" for diode |
| LS, SPK | Loudspeaker or buzzer | |
| M | Motor | |
| MK, MIC | Microphone | |
| MP | Mechanical part (including screws and fasteners) | |
| OP | Opto-isolator | often changed to "U" for IC |
| P | Plug (most-movable connector of a connector pair), plug connector (connector may have "male" pin contacts and/or "female" socket contacts) | |
| PD | Photodiode | |
| Q | Transistor (all types) | |
| R | Resistor | |
| RN | Resistor network | sometimes simplified to "R" for resistor, or "N" for network |
| RT | Thermistor | sometimes simplified to "R" for resistor |
| RV | Varistor, variable resistor | |
| S | Switch (all types, including buttons) | sometimes "SW" is erroneously used |
| SA | Spark arrester | |
| T | Transistor | often changed to "Q", but sometimes "T" is used for bipolar transistors and "Q" for FETs. |
| TC | Thermocouple | |
| TP | Test point | |
| TR, T | Transformer | sometimes changed to "L" for inductor |
| TUN | Tuner | |
| U, IC | Integrated circuit (IC) | shorter "U" (unit) is preferred instead of "IC" |
| V | Vacuum tube | |
| VR | Voltage regulator (voltage reference), or variable resistor (potentiometer / trimmer / rheostat) | voltage regulators are often "U" for IC, pots and trimmers often "R" for resistor |
| X | Socket connector for another item not P or J, paired with the letter symbol for that item (XV for vacuum tube socket, XF for fuse holder, XA for printed circuit assembly connector, XU for integrated circuit connector, XDS for light socket, etc.) | |
| X, XTAL, Y | Crystal, ceramic resonator, powered oscillator | |
| ZD | Zener diode | often changed to "D" for diode |
Other designators
edit- AE: Aerial, antenna
- ASSY: Separable assembly
- B: Battery
- CN: Connector
- CRT: Cathode ray tube
- DSP: Digital signal processor
- FET: Field-effect transistor
- GDT, SVP: Gas discharge tube, surge voltage protector
- H: Pin header
- J, JW: Wire link ("jumper")
- JFET: Junction gate field-effect transistor
- LA: Lightning arrester
- LCD: Liquid crystal display
- LDR: Light-dependent resistor
- LED: Light-emitting diode
- MCB: Miniature circuit breaker
- MIC: Microphone
- MOSFET: Metal-oxide-semiconductor field-effect transistor
- MOV: Metal-oxide varistor
- NE: Neon lamp
- PCB: Printed circuit board
- PLC: Programmable logic controller
- PU: Pickup
- RY, RLA: Relay
- SCR: Silicon-controlled rectifier
- SUS: Silicon unilateral switch
- SW: Switch
- TFT: Thin-film transistor (display)
- TH: Thermistor
- VC: Variable capacitor
- VDR: Voltage-dependent resistor
- VFD: Vacuum fluorescent display
- VT: Voltage transformer
- W: Wire
See also
edit
References
edit- ^ a b Reference Designations for Electrical and Electronics Parts and Equipment: ASME Y14.44-2008(R2014). Fairfield, New Jersey, USA: American Society of Mechanical Engineers. 2014 [2008]. (NB. Replaced IEEE 200-1975.)
- ^ a b c d "Chapter 22. Class Designation Letters". IEEE Standard 315-1975: Graphic Symbols for Electrical and Electronics Diagrams (Including Reference Designation Letters). New York, USA: IEEE / ANSI. 1993-12-02 [1975]. doi:10.1109/IEEESTD.1993.93397. ISBN 978-0-7381-0947-3. Retrieved 2024-07-16. (NB. Reaffirmed 1993.)
- ^ "Section 4.1.5.3 (2)". Standard Reference Designations for Electrical and Electronics Parts and Equipments: IEEE 200-1975. New York, USA: IEEE / ANSI. 1988 [1975]. (NB. Reaffirmed 1988.)
Further reading
edit- "Item Designations; or "Why are relays called 'K' in schematics? Why are circuit breakers called 'Q'?"". Engineering. penwatch.net. 2018-07-01. Archived from the original on 2024-07-17. Retrieved 2024-07-17.
- AS 1103.2-1982 - "Diagrams charts and tables for electrotechnology, Part 2: Item Designation" (Superseded by AS 3702-1989.)
- AS 3702-1989 - "Item designation in electrotechnology". (Equivalent to IEC 60750 Edition 1.0, 1983.)
- IEC 113 (Superseded by IEC 750, i.e. IEC 60750.)
- IEC 750-1983 (AS 3702 is equivalent, but provides extra information.)
- IEEE 315-1975 / ANSI Standard Y32.2. Annex F: "Cross reference list of Class Designation Letters" compares IEC 113-2:1971 to the IEEE/ANSI standard. * AS 1102 and IEC 60617 for "Graphical Symbols for Electrotechnology".