Wikipedia

Semiconductor fabrication plant

(Redirected from Chip fab)

In the microelectronics industry, a semiconductor fabrication plant (commonly called a fab; sometimes foundry) is a factory for semiconductor device fabrication.[1]

GlobalFoundries Fab 1 in Dresden, Germany. The large rectangles house large cleanrooms.
External image
image icon Photo of the interior of a clean room of a 300mm fab run by TSMC

Fabs require many expensive devices to function. Estimates put the cost of building a new fab at over one billion U.S. dollars with values as high as $3–4 billion not being uncommon. TSMC invested $9.3 billion in its Fab15 300 mm wafer manufacturing facility in Taiwan.[2] The same company estimations suggest that their future fab might cost $20 billion.[3] A foundry model emerged in the 1990s: Foundries that produced their own designs were known as integrated device manufacturers (IDMs). Companies that farmed out manufacturing of their designs to foundries were termed fabless semiconductor companies. Those foundries, which did not create their own designs, were called pure-play semiconductor foundries.[4]

The central part of a fab is the clean room, an area where the environment is controlled to eliminate all dust, since even a single speck can ruin a microcircuit, which has nanoscale features much smaller than dust particles. The clean room must also be damped against vibration to enable nanometer-scale alignment of machines and must be kept within narrow bands of temperature and humidity. Vibration control may be achieved by using deep piles in the cleanroom's foundation that anchor the cleanroom to the bedrock, careful selection of the construction site, and/or using vibration dampers. Controlling temperature and humidity is critical for minimizing static electricity. Corona discharge sources can also be used to reduce static electricity. Often, a fab will be constructed in the following manner (from top to bottom): the roof, which may contain air handling equipment that draws, purifies and cools outside air, an air plenum for distributing the air to several floor-mounted fan filter units, which are also part of the cleanroom's ceiling, the cleanroom itself, which may or may not have more than one story, [5] a return air plenum, the clean subfab that may contain support equipment for the machines in the cleanroom such as chemical delivery, purification, recycling and destruction systems, and the ground floor, that may contain electrical equipment. Fabs also often have some office space.

The clean room is where all fabrication takes place and contains the machinery for integrated circuit production such as steppers and/or scanners for photolithography, in addition to etching, cleaning, doping and dicing machines. All these devices are extremely precise and thus extremely expensive. Prices for most common pieces of equipment for the processing of 300 mm wafers range from $700,000 to upwards of $4,000,000 each with a few pieces of equipment reaching as high as $340,000,000 each (e.g. EUV scanners). A typical fab will have several hundred equipment items.

History

edit

Typically an advance in chip-making technology requires a completely new fab to be built. In the past, the equipment to outfit a fab was not very expensive and there were a huge number of smaller fabs producing chips in small quantities. However, the cost of the most up-to-date equipment has since grown to the point where a new fab can cost several billion dollars.

Another side effect of the cost has been the challenge to make use of older fabs. For many companies these older fabs are useful for producing designs for unique markets, such as embedded processors, flash memory, and microcontrollers. However, for companies with more limited product lines, it is often best to either rent out the fab, or close it entirely. This is due to the tendency of the cost of upgrading an existing fab to produce devices requiring newer technology to exceed the cost of a completely new fab.

There has been a trend to produce ever larger wafers, so each process step is being performed on more and more chips at once. The goal is to spread production costs (chemicals, fab time) over a larger number of saleable chips. It is impossible (or at least impracticable) to retrofit machinery to handle larger wafers. This is not to say that foundries using smaller wafers are necessarily obsolete; older foundries can be cheaper to operate, have higher yields for simple chips and still be productive.

The industry was aiming to move from the state-of-the-art wafer size 300 mm (12 in) to 450 mm by 2018.[6] In March 2014, Intel expected 450 mm deployment by 2020.[7] But in 2016, corresponding joint research efforts were stopped.[8]

Additionally, there is a large push to completely automate the production of semiconductor chips from beginning to end. This is often referred to as the "lights-out fab" concept.

The International Sematech Manufacturing Initiative (ISMI), an extension of the US consortium SEMATECH, is sponsoring the "300 mm Prime" initiative. An important goal of this initiative is to enable fabs to produce greater quantities of smaller chips as a response to shorter lifecycles seen in consumer electronics. The logic is that such a fab can produce smaller lots more easily and can efficiently switch its production to supply chips for a variety of new electronic devices. Another important goal is to reduce the waiting time between processing steps.[9][10]

See also

edit

Notes

edit
  1. ^ Brown, Clair; Linden, Greg (2011). Chips and change : how crisis reshapes the semiconductor industry (1st ed.). Cambridge, Mass.: MIT Press. ISBN 9780262516822.
  2. ^ Begins Construction on Gigafab In Central Taiwan Archived 2012-01-29 at the Wayback Machine, issued by TSMC, 16 July 2010
  3. ^ "TSMC says 3nm plant could cost it more than $20bn - TheINQUIRER". theinquirer.net. Archived from the original on 12 October 2017. Retrieved 26 April 2018.{{cite web}}: CS1 maint: unfit URL (link)
  4. ^ Mutschler, Ann Steffora (2008). "Pure-play foundries comprise 84% of market, IC Insights says". Electronics News. Australia: Reed Business Information Pty Ltd, a division of Reed Elsevier Inc.
  5. ^ "SYNUS Tech".
  6. ^ 2011 Report Archived 2012-07-10 at the Wayback Machine - International Technology Roadmap for Semiconductors
  7. ^ "Intel says 450 mm will deploy later in decade". 2014-03-18. Archived from the original on 2014-05-13. Retrieved 2014-05-31.
  8. ^ McGrath, Dylan. "With 450mm on Ice, 300mm Shoulders Heavier Load". Retrieved 3 January 2021.
  9. ^ Chip Makers Watch Their Waste
  10. ^ ISMI Press Release

References

edit
  • Handbook of Semiconductor Manufacturing Technology, Second Edition by Robert Doering and Yoshio Nishi (Hardcover – Jul 9, 2007)
  • Semiconductor Manufacturing Technology by Michael Quirk and Julian Serda (paperback – Nov 19, 2000)
  • Fundamentals of Semiconductor Manufacturing and Process Control by Gary S. May and Costas J. Spanos (hardcover – May 22, 2006)
  • The Essential Guide to Semiconductors (Essential Guide Series) by Jim Turley (paperback – Dec 29, 2002)
  • Semiconductor Manufacturing Handbook (McGraw–Hill Handbooks) by Hwaiyu Geng (hardcover – April 27, 2005)

Semiconductor fabrication softwarehttps://www.einnosys.com/fab-automation/

Further reading

edit
Retrieved from "https://en.wikipedia.org/w/index.php?title=Semiconductor_fabrication_plant&oldid=1241153313"