Wikipedia

GNR Class C1 (large boiler)

(Redirected from LNER Class C1)

The Great Northern Railway (GNR) Class C1 is a type of 4-4-2 steam locomotive. One, ex GNR 251 (later LNER 3251 in 1924, and LNER 2800 in 1946), survives in preservation. Much like their small boiler cousins, they were capable of reaching speeds of up to 90 mph (145 km/h).[2][3] They were also known as Large Atlantics.[4][5]

Great Northern Railway large boiler class C1
London & North Eastern Railway class C1
251, when new in photographic grey
Type and origin
Power typeSteam
DesignerHenry Ivatt
BuilderDoncaster Works
Build date1902–1910
Total produced94[1]
Specifications
Configuration:
​
 • Whyte4-4-2
 • UIC2′B1'
Gauge4 ft 8+1⁄2 in (1,435 mm) standard gauge
Leading dia.3 ft 8 in (1.118 m)
Driver dia.6 ft 8 in (2.032 m)
Trailing dia.3 ft 8 in (1.118 m)
Wheelbase48 ft 5.5 in (14.77 m)
Axle load20 long tons (20 t; 22 short tons)
Adhesive weight40 long tons (41 t; 45 short tons)
Loco weight69.6 long tons (70.7 t; 78.0 short tons)
Tender weight43.1 long tons (43.8 t; 48.3 short tons)
Total weight112.7 long tons (114.5 t; 126.2 short tons)
Tender typeClass B
Fuel typeCoal
Fuel capacity6.5 long tons (6.6 t; 7.3 short tons)
Water cap.3,500 imperial gallons (15,911 L; 4,203 US gal)
Boiler pressure170 psi (1.2 MPa) (Saturated)
150 psi (1.0 MPa) (Superheated)
200 psi (1.4 MPa) (3292 & 1300)
CylindersTwo, outside (Majority), Four (2 outside + 2 inside) on No. 3292 Compound & 3279
Cylinder size19 in × 24 in (483 mm × 610 mm)
or 20 in × 24 in (508 mm × 610 mm) (Majority),
13 in × 20 in (330 mm × 508 mm) (high pressure cylinders on compound)
16 in × 26 in (406 mm × 660 mm) (low pressure cylinders on compound),
15 in × 26 in (381 mm × 660 mm) (No. 3279)
20 in × 26 in (508 mm × 660 mm) (No. 1300)
Valve gearStephenson
Valve typeSlide valves
or 8-inch (203 mm) piston valves (10-inch (254 mm) on 1300)
Performance figures
Tractive effortbetween 13,808 lbf (61.4 kN) and 17,340 lbf (77.1 kN) (Majority),
21,326 lbf (94.9 kN) (3292 compound),
21,128 lbf (94.0 kN) (3279),
22,100 lbf (98.3 kN) (1300)
Career
Operators
Power classBR: 2P
Axle load classLNER: RA: 7
Withdrawn1944-1950
DispositionNo. 251 preserved at the National Collection, remainder scrapped
The preserved 251 at Bressingham

Development

edit

The C1 Class, as it was known under both GNR & LNER classifications, was designed by Henry Ivatt as an enlarged version of what became the LNER C2 Class. The principle of the design was to produce a powerful, free-steaming engine to haul the fastest and heaviest express trains on the Great Northern. They could thus be seen as the start of the East Coast 'Big Engine' policy. None were ever named.

First engine and improvements

edit

The first engine, No. 251, was introduced in 1902, with eighty more being built at Doncaster Works between 1904 and 1908. Although they suffered from a number of teething troubles, the Atlantics were generally very successful. They were originally fitted with slide valves, but later gained piston valves, which produced a notable improvement in performance. The Atlantics remained in front-line service for many years, sometimes being called upon to haul trains of over 500 long tons (508 t; 560 short tons). They were known for reaching speeds of up to 90 miles per hour.[6]

Variants

edit

On the GNR, the classification C1 was used for all of their 4-4-2 tender locomotives, but there was considerable variation within the 116 locomotives making up this group. The LNER divided them into two classes: C2 for the 22 locomotives built in 1898–1903 with boilers of 4 feet 8 inches (1.42 m) diameter; and C1 for the remaining 94, which mostly had boilers of 5 ft 6 in (1.68 m) diameter – but there were several locomotives within the latter group that differed significantly from the others.[7]

The "standard" variety of large-boiler C1 was represented by nos. 251, 272–291, 293–301, 1400–20 and 1422–51 built at Doncaster between 1902 and 1908. These had boilers producing saturated steam at a pressure of 175 lbf/in2 (1,210 kPa) and two outside cylinders, having a diameter of 18+3⁄4 in (480 mm) and a stroke of 24 in (610 mm) using simple expansion driving the rear coupled wheels and fed through slide valves.[8]

No. 292, built at Doncaster in 1904 (but not entering service until 1905), was a four-cylinder compound. The high-pressure cylinders, having a diameter of 13 in (330 mm) and a stroke of 20 in (510 mm), were outside the frames, driving the rear coupled wheels; and the low-pressure cylinders, 16 by 26 in (410 by 660 mm) were inside, driving the front coupled axle. The valves were arranged so that the locomotive could work either as a compound or as a four-cylinder simple. The boiler pressure was 200 lbf/in2 (1,400 kPa), but whilst the boiler was under repair, the locomotive used a 175 lbf/in2 (1,210 kPa) boiler from 1910 to 1912. This locomotive was withdrawn in 1927 and scrapped in 1928.[9]

No. 1300, another four-cylinder compound, was an experimental locomotive which differed greatly from all of the others. It was built by Vulcan Foundry in 1905, largely to their own design although to Ivatt's specifications. The boiler had a narrow firebox, a diameter of 5 ft 3 in (1.60 m) and a pressure of 200 lbf/in2 (1,400 kPa). As with No. 292, the high-pressure cylinders were outside, driving the rear coupled wheels, whilst the low-pressure cylinders were inside, driving the front coupled axle; but their dimensions were 14 by 26 in (360 by 660 mm) and 23 by 26 in (580 by 660 mm) respectively. The engine worked as a two-cylinder simple on starting, changing over to compound expansion automatically. A superheater was fitted in 1914, and the engine was rebuilt as a two-cylinder simple in 1917; the new cylinders were outside, 20 by 26 in (510 by 660 mm) of the type used on class H3, driving the leading coupled wheels. It was withdrawn in 1924.[10]

No. 1421, built at Doncaster in 1907 was again a four-cylinder compound, but differed from No. 292 in a number of ways; in particular, the inside cylinder diameter was increased to 18 in (460 mm). It was superheated in 1914 and rebuilt in 1920 as a two-cylinder simple with piston valves. It was then generally similar to the standard engines after they had been superheated, and it ran until 1947.[11]

The last ten, Nos. 1452–61 built at Doncaster in 1910, had boilers producing superheated steam at 150 lbf/in2 (1,000 kPa), and the cylinders were fed through piston valves.[12]

No. 279 was rebuilt in 1915 with four cylinders 15 by 26 in (380 by 660 mm) utilising simple expansion and driving the rear coupled axle. It was rebuilt back to a two-cylinder simple in 1938, but using 20 by 26 in (510 by 660 mm) cylinders of the type used on class K2 having the piston valves above the cylinders; in this form it ran until 1948.[13][14]

No. 1419 (renumbered 4419 in May 1924) was equipped with a booster engine on the trailing axle in July 1923; to accommodate this, the frames were lengthened at the rear, which also allowed a larger cab to be fitted. At the same time, the locomotive was given a superheater and piston valves, in line with others of the class. The booster, being for extra power at very low speeds, were of little use above speeds of 25mph, was removed temporarily between July 1924 and February 1925, and it was permanently removed in November 1935.[15]

Later years

edit
 
No. 2825 on a stopping train at Seven Sisters, 1946

They were eventually superseded on the heaviest trains by the Gresley A1 Pacifics in the early 1920s. They continued to haul lighter expresses up until 1950, although this did include the Harrogate Pullman for a period during the 1920s and 1930s. They were often called upon to take over trains from failed Pacifics and put up some remarkable performances with loads far in excess of those they were designed to haul. One once took over the Flying Scotsman from a failed A3 at Peterborough and not only made up time but arrived early.

Accidents and incidents

edit
Main article: Grantham rail accident
  • On 19 September 1906, locomotive No. 276 was hauling a sleeper train which was derailed at Grantham, Lincolnshire due to excessive speed through the station after passing signals at danger. Fourteen people were killed and seventeen were injured.[16]
  • On 13 February 1923, locomotive No. 298 was hauling an express passenger train that overran signals and was in a rear-end collision with a freight train at Retford, Nottinghamshire. Three people were killed.[17]
Main article: Welwyn Garden City rail crashes
  • On 15 June 1935, locomotive No. 4411 was hauling a passenger train that was run into by an express passenger train at Welwyn Garden City due to a signalman's error. Fourteen people were killed and 29 were injured.[16]

The last trip

edit

Seventeen C1s survived to serve British Railways, albeit for a short time. According to The Railway Magazine, the last engine in service was BR 62822, ex GNR 294. On 26 November 1950 she hauled a train one way from Kings Cross to Doncaster to mark the end of the C1s. Among the many on board was the son of H.A. Ivatt, Mr. H.G. Ivatt who received one of the builder's plates. On display at Doncaster was pioneer sister ex GNR 251, already preserved, and a number of modern engines. The return trip to London was hauled by A1 Pacific 60123 named, suitably enough, H.A. Ivatt.

The first becomes the last, No. 251

edit

Pioneer 251, LNER 3251 (by 1923) and LNER 2800 (by 1946), had been saved for the UK National Collection even before the last one was withdrawn from revenue service in 1950. Restored to GNR livery, she is the only C1 to survive. She joined preserved sister GNR 990 Henry Oakley on two weekends of trips entitled Plant Centenarian in 1953, celebrating the 100th anniversary of the Doncaster Works.[18] On 20 September the two engines, 990 leading, hauled the train from Kings Cross to Doncaster carrying nearly 500. LNER Class A4 2509 Silver Link (BR 60014) brought the train back to London.[19] A similar trip a week later operated from Kings Cross to Leeds with a stop at Doncaster, with the GNR veterans again hauling one leg of the trip. No. 251 steamed poorly on these trips, because the superheater had been removed although the boiler flues had not been replaced with small tubes to compensate. Further trips followed, the last being on 12 September 1954, but it was not until March 1957 that the locomotive was placed in York museum.[20] Since her preservation, the locomotive has spent time on display at the National Railway Museum, the Locomotion museum in Shildon, Bressingham Steam and Gardens and Barrow Hill Roundhouse. As of 2021, the locomotive is currently on a three-year loan to the new Danum Gallery, Library and Museum in Doncaster.[21]

Surviving boilers

edit

Two C1 boilers, one of which belonged to No. 3287, were discovered at a factory at Essex in 1986 by Steve Dymond and Nick Pigott, the revelation that the boiler once belonged to No. 3287 was unknown until 2005 when it was cleaned via a pressure washer. The boiler that once belonged to No. 3287 was in good condition and was purchased by the Bluebell Railway for their H2 project while the other boiler was scrapped due to it being in bad condition.[22][23][24][25][26][27][28]

References

edit
 
Wikimedia Commons has media related to GNR large boiler Class C1.
  1. ^ Includes four locos built, or rebuilt, with variant dimensions
  2. ^ Train: The Definitive Visual History. Penguin. 2014. p. 96. ISBN 9781465436580. Retrieved 14 October 2020.
  3. ^ Train: The Definitive Visual History. Penguin. 2014. p. 97. ISBN 9781465436580. Retrieved 14 October 2020.
  4. ^ "C1 62808 – 62885 4-4-2 GNR Ivatt Large Atlantic". Preserved British Steam Locomotives. WordPress.com. 9 July 2017. Retrieved 14 December 2020.
  5. ^ "Large Atlantic (C1)". Great Northern Railway Society. Retrieved 14 December 2020.
  6. ^ Train: The Definitive Visual History. DK Press. p. 97.
  7. ^ Boddy, M.G.; Brown, W.A.; Fry, E.V.; Hennigan, W.; Hoole, Ken; Manners, F.; Neve, E.; Platt, E.N.T.; Russell, O.; Yeadon, W.B. (November 1979). Fry, E.V. (ed.). Locomotives of the L.N.E.R., part 3A: Tender Engines – Classes C1 to C11. Kenilworth: RCTS. p. 6. ISBN 0-901115-45-2.
  8. ^ Groves, Norman (1990). Great Northern Locomotive History: Volume 3a 1896-1911 The Ivatt Era. Lincoln: RCTS. pp. 188–9, 192. ISBN 0-901115-69-X.
  9. ^ Groves 1990, pp. 205–6
  10. ^ Groves 1990, pp. 206–9
  11. ^ Groves 1990, pp. 210–1
  12. ^ Groves 1990, pp. 188–9
  13. ^ Groves 1990, pp. 211–9
  14. ^ Boddy et al. 1979, pp. 23–26
  15. ^ Boddy et al. 1979, pp. 26, 29, 48
  16. ^ a b Hoole, Ken (1982). Trains in Trouble: Vol. 3. Redruth: Atlantic Books. pp. 14, 31. ISBN 0-906899-05-2.
  17. ^ Hall, Stanley (1990). The Railway Detectives. London: Ian Allan. p. 83. ISBN 0-7110-1929-0.
  18. ^ "Doncaster Works Centenary Tours". Notes and News. The Railway Magazine. Vol. 99, no. 629. Westminster: Tothill Press. September 1953. pp. 641–2.
  19. ^ "The Railtour Files".
  20. ^ Groves 1990, pp. 229–230
  21. ^ "Doncaster-built locomotive returns home". National Railway Museum. Science Museum Group. 25 January 2021. Retrieved 26 January 2021.
  22. ^ Salmon, Richard. "Bluebell Railway Atlantic Group Background and early progress". Bluebell Railway Atlantic Group. Bluebell Railway. Retrieved 19 October 2020.
  23. ^ Carr, Bob. "Notes and news – August 2017: In a London laundry?". GLIAS. GREATER LONDON INDUSTRIAL ARCHAEOLOGY SOCIETY. Retrieved 19 October 2020.
  24. ^ Carr, Bob. "The re-use of locomotives boilers in industry". Notes and news – October 2017: The re-use of locomotives boilers in industry. GREATER LONDON INDUSTRIAL ARCHAEOLOGY SOCIETY. Retrieved 19 October 2020.
  25. ^ Sturt, Brian. "Notes and news – October 2017: Boiler for 'Beachy Head'". GLIAS. GREATER LONDON INDUSTRIAL ARCHAEOLOGY SOCIETY. Retrieved 19 October 2020.
  26. ^ Bright, Thomas. "A profile of the replica Brighton 'Atlantic' now nearing completion". Steam Railway. Retrieved 24 July 2020 – via Press Reader.
  27. ^ Nodes, Lewis. "The Brighton Atlantic Project: Announcement of Intention". The Brighton Atlantic Project. Retrieved 11 June 2004.
  28. ^ Baldwin, James S. (30 August 2017). Brighton Atlantics. Pen & Sword Books. ISBN 9781473869370. Retrieved 19 October 2020.
Retrieved from "https://en.wikipedia.org/w/index.php?title=GNR_Class_C1_(large_boiler)&oldid=1246714136"