List of ISO standards 14000–15999

This is a list of published^{[Note 1]} International Organization for Standardization (ISO) standards and other deliverables.^{[Note 2]} For a complete and up-to-date list of all the ISO standards, see the ISO catalogue.^[1]

The standards are protected by copyright and most of them must be purchased. However, about 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 (JTC 1) have been made freely and publicly available.^[2]

ISO 14000 – ISO 14999

ISO 14000 Environmental management systems (This is a set of standards, rather than a single standard)
ISO 14001:2015 Environmental management systems – Requirements with guidance for use
ISO 14004:2016 Environmental management systems – General guidelines on implementation
ISO 14005:2010 Environmental management systems – Guidelines for the phased implementation of an environmental management system, including the use of environmental performance evaluation
ISO 14006:2011 Environmental management systems – Guidelines for incorporating ecodesign
ISO 14015:2022 Environmental management — Guidelines for environmental due diligence assessment
ISO 14020:2000 Environmental labels and declarations – General principles
ISO 14031 Environmental management - Environmental performance evaluation – Guidelines
ISO 14045:2012 describes the principles, requirements and guidelines for eco-efficiency assessment for product systems ^[3]
ISO 14046:2014 - Environmental management — Water footprint — Principles, requirements and guidelines
ISO 14050:2009 Environmental management – Vocabulary
ISO 14051 Environmental management – Material flow cost accounting - General framework
ISO 14064 Greenhouse gases
ISO/TR 14073:2017 Environmental management - Water footprint - Illustrative examples on how to apply ISO 14046
ISO 14084 Process diagrams for power plants
- ISO 14084-1:2015 Part 1: Specification for diagrams
- ISO 14084-2:2015 Part 2: Graphical symbols
ISO/TS 14101:2012 Surface characterization of gold nanoparticles for nanomaterial specific toxicity screening: FT-IR method
ISO/IEC 14102:2008 Information technology - Guideline for the evaluation and selection of CASE tools
ISO/TR 14105:2011 Document management - Change management for successful electronic document management system (EDMS) implementation
ISO 14117:2012 Active implantable medical devices – Electromagnetic compatibility – EMC test protocols for implantable cardiac pacemakers, implantable cardioverter defibrillators and cardiac resynchronization devices
ISO 14132 Optics and photonics - Vocabulary for telescopic systems
- ISO 14132-1:2015 Part 1: General terms and alphabetical indexes of terms in ISO 14132
- ISO 14132-2:2015 Part 2: Terms for binoculars, monoculars and spotting scopes
- ISO 14132-3:2014 Part 3: Terms for telescopic sights
- ISO 14132-4:2015 Part 4: Terms for astronomical telescopes
- ISO 14132-5:2008 Part 5: Terms for night vision devices
ISO/IEC 14136:1995 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Identification supplementary services
ISO 14139:2000 Hydrometric determinations – Flow measurements in open channels using structures – Compound gauging structures
ISO/IEC 14143 Information technology - Software measurement - Functional size measurement
- ISO/IEC 14143-1:2007 Part 1: Definition of concepts
- ISO/IEC 14143-2:2011 Part 2: Conformity evaluation of software size measurement methods to ISO/IEC 14143-1
- ISO/IEC TR 14143-3:2003 Part 3: Verification of functional size measurement methods
- ISO/IEC TR 14143-4:2002 Part 4: Reference model
- ISO/IEC TR 14143-5:2004 Part 5: Determination of functional domains for use with functional size measurement
- ISO/IEC 14143-6:2012 Part 6: Guide for use of ISO/IEC 14143 series and related International Standards
ISO 14145 Roller ball pens and refills
- ISO 14145-2:1998 Part 2: Documentary use (DOC)
ISO 14155:2011 Clinical investigation of medical devices for human subjects – Good clinical practice
ISO 14163:1998 Acoustics – Guidelines for noise control by silencers
ISO 14164:1999 Stationary source emissions – Determination of the volume flowrate of gas streams in ducts – Automated method
ISO/IEC 14165 Information technology - Fibre Channel
- ISO/IEC 14165-114:2005 Part 114: 100 MB/s Balanced copper physical interface (FC-100-DF-EL-S)
- ISO/IEC 14165-115:2006 Part 115: Physical Interfaces (FC-PI)
- ISO/IEC 14165-116:2005 Part 116: 10 Gigabit (10GFC)
- ISO/IEC TR 14165-117:2007 Part 117: Methodologies for jitter and signal quality (MJSQ)
- ISO/IEC 14165-122:2005 Part 122: Arbitrated Loop-2 (FC-AL-2)
- ISO/IEC 14165-131:2000 Part 131: Switch Fabric Requirements (FC-SW)
- ISO/IEC 14165-133:2010 Part 133: Switch Fabric-3 (FC-SW-3)
- ISO/IEC 14165-141:2001 Part 141: Fabric Generic Requirements (FC-FG)
- ISO/IEC 14165-211:1999 Part 211: Mapping to HIPPI-FP (FC-FP)
- ISO/IEC 14165-222:2005 Part 222: Single-byte command code 2 mapping protocol (FC-SB-2)
- ISO/IEC 14165-241:2005 Part 241: Backbone 2 (FC-BB-2)
- ISO/IEC 14165-243:2012 Part 243: Backbone 3 (FC-BB-3)
- ISO/IEC 14165-251:2008 Part 251: Framing and Signaling (FC-FS)
- ISO/IEC TR 14165-312:2009 Part 312: Avionics environment upper layer protocol MIL-STD-1553B Notice 2 (FC-AE-1553)
- ISO/IEC TR 14165-313:2013 Part 313: Avionics Environment—Anonymous Synchronous Messaging (FC-AE-ASM)
- ISO/IEC TR 14165-314:2013 Part 314: Avionics Environment – Remote Direct Memory Access (FC-AE-RDMA)
- ISO/IEC 14165-321:2009 Part 321: Audio-Video (FC-AV)
- ISO/IEC 14165-331:2007 Part 331: Virtual Interface (FC-VI)
- ISO/IEC TR 14165-372:2011 Part 372: Methodologies of interconnects-2 (FC-MI-2)
- ISO/IEC 14165-414:2007 Part 414: Generic Services—4 (FC-GS-4)
- ISO/IEC 14165-521:2009 Part 521: Fabric application interface standard (FAIS)
ISO/IEC 14169:1995 Information technology – 90 mm flexible disk cartridges – 21 MB formatted capacity – ISO Type 305
ISO 14189:2013 Water quality – Enumeration of Clostridium perfringens – Method using membrane filtration
ISO 14199:2015 Health informatics – Information models – Biomedical Research Integrated Domain Group (BRIDG) Model
ISO 14223 Radiofrequency identification of animals – Advanced transponders
ISO 14224 Petroleum, petrochemical and natural gas industries - Collection and exchange of reliability and maintenance data for equipment
ISO 14230 Road vehicles – Diagnostic systems – Keyword Protocol 2000
ISO 14242 Implants for surgery – Wear of total hip-joint prostheses
- ISO 14242-1:2014 Part 1: Loading and displacement parameters for wear-testing machines and corresponding environmental conditions for test
- ISO 14242-2:2016 Part 2: Methods of measurement
- ISO 14242-3:2009 Part 3: Loading and displacement parameters for orbital bearing type wear testing machines and corresponding environmental conditions for test
ISO 14243 Implants for surgery – Wear of total knee-joint prostheses
- ISO 14243-1:2009 Part 1: Loading and displacement parameters for wear-testing machines with load control and corresponding environmental conditions for test
- ISO 14243-2:2016 Part 2: Methods of measurement
- ISO 14243-3:2014 Part 3: Loading and displacement parameters for wear-testing machines with displacement control and corresponding environmental conditions for test
ISO/IEC 14251:1995 Information technology – Data interchange on 12.7 mm 36-track magnetic tape cartridges
ISO/IEC TR 14252:1996 Information technology - Guide to the POSIX Open System Environment (OSE) [Withdrawn without replacement]
ISO 14253 Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment
- ISO 14253-1:2013 Part 1: Decision rules for proving conformity or nonconformity with specifications
- ISO 14253-2:2011 Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
- ISO 14253-3:2011 Part 3: Guidelines for achieving agreements on measurement uncertainty statements
- ISO/TS 14253-4:2010 Part 4: Background on functional limits and specification limits in decision rules
- ISO 14253-5:2015 Part 5: Uncertainty in verification testing of indicating measuring instruments
- ISO/TR 14253-6:2012 Part 6: Generalized decision rules for the acceptance and rejection of instruments and workpieces
ISO/TS 14265:2011 Health Informatics – Classification of purposes for processing personal health information
ISO/TR 14283:2004 Implants for surgery – Fundamental principles
ISO 14289 Document management applications - Electronic document file format enhancement for accessibility
- ISO 14289-1:2014 Part 1: Use of ISO 32000-1 (PDF/UA-1)
ISO/TR 14292:2012 Health informatics – Personal health records – Definition, scope and context
ISO 14296:2016 Intelligent transport systems – Extension of map database specifications for applications of cooperative ITS
ISO 14302:2002 Space systems – Electromagnetic compatibility requirements
ISO 14362 Textiles - Methods for determination of certain aromatic amines derived from azo colorants
- ISO 14362-1:2017 Part 1: Detection of the use of certain azo colorants accessible with and without extracting the fibres
- ISO 14362-3:2017 Part 3: Detection of the use of certain azo colorants, which may release 4-aminoazobenzene
ISO/IEC TR 14369:2018 Information technology – Programming languages, their environments and system software interfaces – Guidelines for the preparation of language-independent service specifications (LISS)
ISO 14405 Geometrical product specifications (GPS) – Dimensional tolerancing
- ISO 14405-1:2016 Part 1: Linear sizes
- ISO 14405-2:2011 Part 2: Dimensions other than linear sizes
- ISO 14405-3:2016 Part 3: Angular sizes
ISO 14406:2010 Geometrical product specifications (GPS) - Extraction
ISO 14408:2016 Tracheal tubes designed for laser surgery – Requirements for marking and accompanying information
ISO 14416:2003 Information and documentation – Requirements for binding of books, periodicals, serials and other paper documents for archive and library use – Methods and materials
ISO/IEC 14417:1999 Information technology – Data recording format DD-1 for magnetic tape cassette conforming to IEC 1016
ISO/TS 14441:2013 Health informatics – Security and privacy requirements of EHR systems for use in conformity assessment
ISO/IEC 14443 Identification cards – Contactless integrated circuit cards – Proximity cards
ISO 14451 Pyrotechnic articles – Pyrotechnic articles for vehicles
- ISO 14451-1:2013 Part 1: Terminology
ISO 14452:2012 Network services billing – Requirements
ISO 14461 Milk and milk products – Quality control in microbiological laboratories
- ISO 14461-1:2005 Part 1: Analyst performance assessment for colony counts
- ISO 14461-2:2005 Part 2: Determination of the reliability of colony counts of parallel plates and subsequent dilution steps
ISO/IEC 14462:2010 Information technology - Open-edi reference model
ISO/TR 14468:2010 Selected illustrations of attribute agreement analysis
ISO/IEC TR 14471:2007 Information technology - Software engineering - Guidelines for the adoption of CASE tools
ISO/IEC 14473:1999 Information technology - Office equipment - Minimum information to be specified for image scanners
ISO/IEC 14474:1998 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Functional requirements for static circuit-mode inter-PINX connections
ISO/IEC TR 14475:2001 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Architecture and scenarios for Private Integrated Services Networking
ISO/IEC 14476 Information technology – Enhanced communications transport protocol
- ISO/IEC 14476-1:2002 Specification of simplex multicast transport
- ISO/IEC 14476-2:2003 Specification of QoS management for simplex multicast transport
- ISO/IEC 14476-3:2008 Specification of duplex multicast transport
- ISO/IEC 14476-4:2010 Specification of QoS management for duplex multicast transport
- ISO/IEC 14476-5:2008 Specification of N-plex multicast transport
- ISO/IEC 14476-6:2010 Specification of QoS management for n-plex multicast transport
ISO/IEC 14478 Information technology - Computer graphics and image processing - Presentation Environment for Multimedia Objects (PREMO)
- ISO/IEC 14478-1:1998 Part 1: Fundamentals of PREMO
- ISO/IEC 14478-2:1998 Part 2: Foundation Component
- ISO/IEC 14478-3:1998 Part 3: Multimedia Systems Services
- ISO/IEC 14478-4:1998 Part 4: Modelling, rendering and interaction component
ISO/IEC 14492:2001 Information technology - Lossy/lossless coding of bi-level images
ISO/IEC 14495 Information technology - Lossless and near-lossless compression of continuous-tone still images
- ISO/IEC 14495-1:1999 Baseline
- ISO/IEC 14495-2:2003 Extensions
ISO/IEC 14496 Information technology – Coding of audio-visual objects
ISO 14500:2003 Textile machinery and accessories – Harnesses for Jacquard weaving machines – Vocabulary
ISO 14509 Small craft – Airborne sound emitted by powered recreational craft
- ISO 14509-1:2008 Part 1: Pass-by measurement procedures
- ISO 14509-3:2009 Part 3: Sound assessment using calculation and measurement procedures
ISO 14511:2001 Measurement of fluid flow in closed conduits – Thermal mass flowmeters
ISO/IEC 14515 Information technology - Portable Operating System Interface (POSIX) - Test methods for measuring conformance to POSIX
- ISO/IEC 14515-1:2000 Part 1: System interfaces
ISO/IEC TR 14516:2002 Information technology - Security techniques - Guidelines for the use and management of Trusted Third Party services
ISO/IEC 14517:1996 Information technology - 130 mm optical disk cartridges for information interchange - Capacity: 2.6 GB per cartridge
ISO/IEC 14519:2001 Information technology - POSIX Ada Language Interfaces - Binding for System Application Program Interface (API)
ISO 14532:2014 Natural gas – Vocabulary
ISO 14533 Processes, data elements and documents in commerce, industry and administration – Long term signature profiles
- ISO 14533-1:2014 Part 1: Long term signature profiles for CMS Advanced Electronic Signatures (CAdES)
- ISO 14533-2:2012 Part 2: Long term signature profiles for XML Advanced Electronic Signatures (XAdES)
- ISO 14533-3:2017 Part 3: Long term signature profiles for PDF Advanced Electronic Signatures (PAdES)
ISO 14534:2011 Ophthalmic optics – Contact lenses and contact lens care products – Fundamental requirements
ISO 14539:2000 Manipulating industrial robots - Object handling with grasp-type grippers - Vocabulary and presentation of characteristics
ISO/IEC 14543 Information technology – Home Electronic System (HES) architecture
- ISO/IEC 14543-2-1:2006 Part 2-1: Introduction and device modularity
- ISO/IEC 14543-3-1:2006 Part 3-1: Communication layers – Application layer for network based control of HES Class 1
- ISO/IEC 14543-3-2:2006 Part 3-2: Communication layers – Transport, network and general parts of data link layer for network based control of HES Class 1
- ISO/IEC 14543-3-3:2007 Part 3-3: User process for network based control of HES Class 1
- ISO/IEC 14543-3-4:2007 Part 3-4: System management – Management procedures for network based control of HES Class 1
- ISO/IEC 14543-3-5:2007 Part 3-5: Media and media dependent layers – Power line for network based control of HES Class 1
- ISO/IEC 14543-3-6:2007 Part 3-6: Media and media dependent layers – Network based on HES Class 1, twisted pair
- ISO/IEC 14543-3-7:2007 Part 3-7: Media and media dependent layers – Radio frequency for network based control of HES Class 1
- ISO/IEC 14543-3-10:2012 Part 3-10: Wireless short-packet (WSP) protocol optimized for energy harvesting – Architecture and lower layer protocols
- ISO/IEC 14543-3-11:2016 Part 3-11: Frequency modulated wireless short-packet (FMWSP) protocol optimised for energy harvesting – Architecture and lower layer protocols
- ISO/IEC TR 14543-4:2002 Part 4: Home and building automation in a mixed-use building
- ISO/IEC 14543-4-1:2008 Part 4-1: Communication layers – Application layer for network enhanced control devices of HES Class 1
- ISO/IEC 14543-4-2:2008 Part 4-2: Communication layers – Transport, network and general parts of data link layer for network enhanced control devices of HES Class 1
- ISO/IEC 14543-4-3:2015 Part 4-3: Application layer interface to lower communications layers for network enhanced control devices of HES Class 1
- ISO/IEC 14543-5-1:2010 Part 5-1: Intelligent grouping and resource sharing for Class 2 and Class 3 – Core protocol
- ISO/IEC 14543-5-3:2012 Part 5-3: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Basic application
- ISO/IEC 14543-5-4:2010 Part 5-4: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Device validation
- ISO/IEC 14543-5-5:2012 Part 5-5: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Device type
- ISO/IEC 14543-5-6:2012 Part 5-6: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Service type
- ISO/IEC 14543-5-7:2015 Part 5-7: Intelligent grouping and 3 resource sharing – Remote access system architecture
- ISO/IEC 14543-5-8:2017 Part 5-8: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Remote access core protocol
- ISO/IEC 14543-5-9:2017 Part 5-9: Intelligent grouping and resource sharing for HES class 2 and class 3 – Remote access service platform
- ISO/IEC 14543-5-21:2012 Part 5-21: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Application profile – AV profile
- ISO/IEC 14543-5-22:2010 Part 5-22: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Application profile – File profile
ISO 14560:2004 Acceptance sampling procedures by attributes - Specified quality levels in nonconforming items per million
ISO/TR 14564:1995 Shipbuilding and marine structures - Marking of escape routes
ISO/IEC 14568:1997 Information technology - DXL: Diagram eXchange Language for tree-structured charts
ISO/IEC 14575:2000 Information technology - Microprocessor systems - Heterogeneous InterConnect (HIC) (Low-Cost, Low-Latency Scalable Serial Interconnect for Parallel System Construction)
ISO/IEC 14576:1999 Information technology - Synchronous Split Transfer Type System Bus (STbus) - Logical Layer
ISO 14580:2011 Hexalobular socket cheese head screws
ISO 14588:2000 Blind rivets - Terminology and definitions
ISO/IEC 14598 Software engineering - Product evaluation^{[Note 3]}
- ISO/IEC 14598-5:1998 Part 5: Process for evaluators
- ISO/IEC 14598-6:2001 Part 6: Documentation of evaluation modules
ISO 14602:2010 Non-active surgical implants – Implants for osteosynthesis – Particular requirements
ISO 14607:2007 Non-active surgical implants – Mammary implants – Particular requirements
ISO 14617 Graphical symbols for diagrams
- ISO 14617-1:2005 Part 1: General information and indexes
- ISO 14617-2:2002 Part 2: Symbols having general application
- ISO 14617-3:2002 Part 3: Connections and related devices
- ISO 14617-3:2002 Part 3: Connections and related devices
- ISO 14617-4:2002 Part 4: Actuators and related devices
- ISO 14617-5:2002 Part 5: Measurement and control devices
- ISO 14617-6:2002 Part 6: Measurement and control functions
- ISO 14617-7:2002 Part 7: Basic mechanical components
- ISO 14617-8:2002 Part 8: Valves and dampers
- ISO 14617-9:2002 Part 9: Pumps, compressors and fans
- ISO 14617-10:2002 Part 10: Fluid power converters
- ISO 14617-11:2002 Part 11: Devices for heat transfer and heat engines
- ISO 14617-12:2002 Part 12: Devices for separating, purification and mixing
- ISO 14617-13:2004 Part 13: Devices for material processing
- ISO 14617-14:2004 Part 14: Devices for transport and handling of material
- ISO 14617-15:2002 Part 15: Installation diagrams and network maps
ISO 14630:2012 Non-active surgical implants – General requirements
ISO 14638:2015 Geometrical product specifications (GPS) - Matrix model
ISO/TR 14639 Health informatics – Capacity-based eHealth architecture roadmap
- ISO/TR 14639-1:2012 Part 1: Overview of national eHealth initiatives
- ISO/TR 14639-2:2014 Part 2: Architectural components and maturity model
ISO 14641 Electronic archiving
- ISO 14641-1:2012 Specifications concerning the design and the operation of an information system for electronic information preservation
ISO 14644 Cleanrooms and associated controlled environments
ISO/IEC 14651:2020 Information technology — International string ordering and comparison — Method for comparing character strings and description of the common template tailorable ordering
ISO/IEC 14662:2010 Information technology – Open-edi reference model
ISO/TR 14685:2001 Hydrometric determinations – Geophysical logging of boreholes for hydrogeological purposes – Considerations and guidelines for making measurements
ISO 14686:2003 Hydrometric determinations – Pumping tests for water wells – Considerations and guidelines for design, performance and use
ISO 14695:2003 Industrial fans – Method of measurement of fan vibration
ISO 14698 Cleanrooms and associated controlled environments – Biocontamination control
- ISO 14698-1:2003 General principles and methods
- ISO 14698-2:2003 Evaluation and interpretation of biocontamination data
ISO/IEC 14699:1997 Information technology – Open Systems Interconnection – Transport Fast Byte Protocol
ISO/IEC 14700:1997 Information technology – Open Systems Interconnection – Network Fast Byte Protocol
ISO 14708 Implants for surgery – Active implantable medical devices
- ISO 14708-1:2014 Part 1: General requirements for safety, marking and for information to be provided by the manufacturer
- ISO 14708-2:2012 Part 2: Cardiac pacemakers
- ISO 14708-3:2017 Part 3: Implantable neurostimulators
- ISO 14708-4:2008 Part 4: Implantable infusion pumps
- ISO 14708-5:2010 Part 5: Circulatory support devices
- ISO 14708-6:2010 Part 6: Particular requirements for active implantable medical devices intended to treat tachyarrhythmia (including implantable defibrillators)
- ISO 14708-7:2013 Part 7: Particular requirements for cochlear implant systems
ISO/IEC 14709 Information technology - Configuration of Customer Premises Cabling (CPC) for applications
- ISO/IEC 14709-1:1997 Part 1: Integrated Services Digital Network (ISDN) basic access
- ISO/IEC 14709-2:1998 Part 2: Integrated Services Digital Network (ISDN) primary rate
ISO 14722:1998 Moped and moped-rider kinematics – Vocabulary
ISO 14726:2008 Ships and marine technology – Identification colours for the content of piping systems
ISO 14729:2001 Ophthalmic optics – Contact lens care products – Microbiological requirements and test methods for products and regimens for hygienic management of contact lenses
ISO 14730:2014 Ophthalmic optics – Contact lens care products – Antimicrobial preservative efficacy testing and guidance on determining discard date
ISO 14739 Document management - 3D use of Product Representation Compact (PRC) format
- ISO 14739-1:2014 Part 1: PRC 10001
ISO/TR 14742:2010 Financial services – Recommendations on cryptographic algorithms and their use
ISO/IEC 14750:1999 Information technology – Open Distributed Processing – Interface Definition Language
ISO/IEC 14752:2000 Information technology - Open Distributed Processing - Protocol support for computational interactions
ISO/IEC 14753:1999 Information technology - Open Distributed Processing - Interface references and binding
ISO/IEC 14754:1999 Information technology – Pen-Based Interfaces – Common gestures for Text Editing with Pen-Based Systems
ISO/IEC 14755:1997 Information technology – Input methods to enter characters from the repertoire of ISO/IEC 10646 with a keyboard or other input device
ISO/IEC 14756:1999 Information technology - Measurement and rating of performance of computer-based software systems
ISO/IEC 14760:1997 Information technology - Data interchange on 90 mm overwritable and read only optical disk cartridges using phase change - Capacity: 1.3 GB per cartridge
ISO/IEC 14762:2009 Information technology - Functional safety requirements for Home and Building Electronic Systems (HBES)
ISO/IEC 14763 Information technology - Implementation and operation of customer premises cabling
- ISO/IEC 14763-1:1999 Part 1: Administration
- ISO/IEC 14763-2:2012 Part 2: Planning and installation
- ISO/IEC TR 14763-2-1:2011 Part 2-1: Planning and installation - Identifiers within administration systems
- ISO/IEC 14763-3:2014 Part 3: Testing of optical fibre cabling
ISO/IEC 14764:2006 Software Engineering - Software Life Cycle Processes - Maintenance
ISO/IEC 14765:1997 Information technology - Framework for protocol identification and encapsulation
ISO/IEC 14766:1997 Information technology - Telecommunications and information exchange between systems - Use of OSI applications over the Internet Transmission Control Protocol (TCP)
ISO/IEC 14769:2001 Information technology - Open Distributed Processing - Type Repository Function
ISO/IEC 14771:1999 Information technology - Open Distributed Processing - Naming framework
ISO/IEC 14772 Information technology - Computer graphics and image processing - The Virtual Reality Modeling Language (VRML)^{[Note 3]}
- ISO/IEC 14772-1:1997 Part 1: Functional specification and UTF-8 encoding
- ISO/IEC 14772-2:2004 Part 2: External authoring interface (EAI)
ISO/IEC 14776 Information technology - Small Computer System Interface (SCSI)^{[Note 3]}
- ISO/IEC 14776-112:2002 Part 112: Parallel Interface-2 (SPI-2)
- ISO/IEC 14776-113:2002 Part 113: Parallel Interface-3 (SPI-3)
- ISO/IEC 14776-115:2004 Part 115: Parallel Interface-5 (SPI-5)
- ISO/IEC 14776-121:2010 Part 121: Passive Interconnect Performance (PIP)
- ISO/IEC 14776-150:2004 Part 150: Serial Attached SCSI (SAS)
- ISO/IEC 14776-151:2010 Part 151: Serial Attached SCSI - 1.1 (SAS-1.1)
- ISO/IEC 14776-153:2015 Part 153: Serial Attached SCSI - 2.1 (SAS-2.1)
- ISO/IEC 14776-154:2017 Part 154: Serial Attached SCSI – 3 (SAS-3)
- ISO/IEC 14776-222:2005 Part 222: Fibre Channel Protocol for SCSI, Second Version (FCP-2)
- ISO/IEC 14776-223:2008 Part 223: Fibre Channel Protocol for SCSI, Third Version (FCP-3)
- ISO/IEC 14776-232:2001 Part 232: Serial Bus Protocol 2 (SBP-2)
- ISO/IEC 14776-251:2014 Part 251: USB attached SCSI (UAS)
- ISO/IEC 14776-261:2012 Part 261: SAS Protocol Layer (SPL)
- ISO/IEC 14776-262:2017 Part 262: SAS protocol layer - 2 (SPL-2)
- ISO/IEC 14776-321:2002 Part 321: SCSI-3 Block Commands (SBC)
- ISO/IEC 14776-322:2007 Part 322: SCSI Block Commands - 2 (SBC-2)
- ISO/IEC 14776-323:2017 Part 323: SCSI Block commands - 3 (SBC-3)
- ISO/IEC 14776-326:2015 Part 326: Reduced block commands (RBC)
- ISO/IEC 14776-331:2002 Part 331: Stream Commands (SSC)
- ISO/IEC 14776-333:2013 Part 333: SCSI Stream Commands - 3 (SSC-3)
- ISO/IEC 14776-341:2000 Part 341: Controller Commands (SCC)
- ISO/IEC 14776-342:2000 Part 342: Controller Commands - 2 (SCC-2)
- ISO/IEC 14776-351:2007 Part 351: Medium Changer Commands (SCSI-3 SMC)
- ISO/IEC 14776-362:2006 Part 362: Multimedia commands-2 (MMC-2)
- ISO/IEC 14776-372:2011 Part 372: SCSI Enclosure Services - 2 (SES-2)
- ISO/IEC 14776-381:2000 Part 381: Optical Memory Card Device Commands (OMC)
- ISO/IEC 14776-411:1999 Part 411: SCSI-3 Architecture Model (SCSI-3 SAM)
- ISO/IEC 14776-412:2006 Part 412: Architecture Model -2 (SAM-2)
- ISO/IEC 14776-413:2007 Part 413: SCSI Architecture Model -3 (SAM-3)
- ISO/IEC 14776-414:2009 Part 414: SCSI Architecture Model-4 (SAM-4)
- ISO/IEC 14776-452:2005 Part 452: SCSI Primary Commands - 2 (SPC-2)
- ISO/IEC 14776-453:2009 Part 453: Primary commands-3 (SPC-3)
ISO 14785:2014 Tourist information offices – Tourist information and reception services – Requirements
ISO/TR 14786:2014 Nanotechnologies – Considerations for the development of chemical nomenclature for selected nano-objects
ISO 14801 Dentistry – Implants – Dynamic fatigue test for endosseous dental implants
ISO/TR 14806:2013 Intelligent transport systems – Public transport requirements for the use of payment applications for fare media
ISO 14813 Intelligent transport systems – Reference model architecture(s) for the ITS sector
- ISO 14813-1:2015 Part 1: ITS service domains, service groups and services
- ISO 14813-5:2010 Part 5: Requirements for architecture description in ITS standards
- ISO 14813-6:2009 Part 6: Data presentation in ASN.1
ISO 14814:2006 Road transport and traffic telematics – Automatic vehicle and equipment identification – Reference architecture and terminology
ISO 14815:2005 Road transport and traffic telematics – Automatic vehicle and equipment identification – System specifications
ISO 14816:2005 Road transport and traffic telematics – Automatic vehicle and equipment identification – Numbering and data structure
ISO 14817 Intelligent transport systems – ITS central data dictionaries
- ISO 14817-1:2015 Part 1: Requirements for ITS data definitions
- ISO 14817-2:2015 Part 2: Governance of the Central ITS Data Concept Registry
- ISO 14817-3:2017 Part 3: Object identifier assignments for ITS data concepts
ISO 14819 Intelligent transport systems – Traffic and travel information messages via traffic message coding
- ISO 14819-1:2013 Part 1: Coding protocol for Radio Data System – Traffic Message Channel (RDS-TMC) using ALERT-C
- ISO 14819-2:2013 Part 2: Event and information codes for Radio Data System – Traffic Message Channel (RDS-TMC) using ALERT-C
- ISO 14819-3:2013 Part 3: Location referencing for Radio Data System – Traffic Message Channel (RDS-TMC) using ALERT-C
- ISO 14819-6:2006 Part 6: Encryption and conditional access for the Radio Data System – Traffic Message Channel ALERT C coding
ISO 14823:2017 Intelligent transport systems – Graphic data dictionary
ISO 14825:2011 Intelligent transport systems – Geographic Data Files (GDF) – GDF5.0
ISO 14827 Transport information and control systems – Data interfaces between centres for transport information and control systems
- ISO 14827-1:2005 Part 1: Message definition requirements
- ISO 14827-2:2005 Part 2: DATEX-ASN
ISO/IEC 14833:1996 Information technology – Data interchange on 12.7 mm 128-Track magnetic tape cartridges – DLT 3 format
ISO/IEC 14834:1996 Information technology - Distributed Transaction Processing - The XA Specification
ISO 14837 Mechanical vibration – Ground-borne noise and vibration arising from rail systems
- ISO 14837-1:2005 Part 1: General guidance
- ISO/TS 14837-31:2017 Part 31: Guideline on field measurements for the evaluation of human exposure in buildings
- ISO/TS 14837-32:2015 Part 32: Measurement of dynamic properties of the ground
ISO 14839 Mechanical vibration - Vibration of rotating machinery equipped with active magnetic bearings
- ISO 14839-1:2002 Part 1: Vocabulary
- ISO 14839-2:2004 Part 2: Evaluation of vibration
- ISO 14839-3:2006 Part 3: Evaluation of stability margin
- ISO 14839-4:2012 Part 4: Technical guidelines
ISO/IEC 14840:1996 Information technology – 12.65 mm wide magnetic tape cartridge for information interchange – Helical scan recording – Data-D3-1 format
ISO/IEC 14841:1996 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Call offer supplementary service
ISO/IEC 14842:1996 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Do not disturb and do not disturb override supplementary services
ISO/IEC 14843:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Call Offer supplementary service
ISO/IEC 14844:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Do Not Disturb and Do Not Disturb Override supplementary services
ISO/IEC 14845:1996 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Call intrusion supplementary service
ISO/IEC 14846:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Call Intrusion supplementary service
ISO 14855 Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions – Method by analysis of evolved carbon dioxide
- ISO 14855-1:2012 General method
- ISO 14855-2:2007 Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test
ISO/IEC 14863:1996 Information technology - System-Independent Data Format (SIDF)
ISO/TR 14873:2013 Information and documentation - Statistics and quality issues for web archiving
ISO 14879 Implants for surgery – Total knee-joint prostheses
- ISO 14879-1:2000 Part 1: Determination of endurance properties of knee tibial trays
ISO 14880 Optics and photonics - Microlens arrays
- ISO 14880-1:2016 Part 1: Vocabulary and general properties
- ISO 14880-2:2006 Part 2: Test methods for wavefront aberrations
- ISO 14880-3:2006 Part 3: Test methods for optical properties other than wavefront aberrations
- ISO 14880-4:2006 Part 4: Test methods for geometrical properties
- ISO/TR 14880-5:2010 Part 5: Guidance on testing
ISO 14881:2001 Integrated optics – Interfaces – Parameters relevant to coupling properties
ISO/IEC 14882:2020 Programming languages — C++
ISO/IEC 14888 Information technology - Security techniques - Digital signatures with appendix
- ISO/IEC 14888-1:2008 Part 1: General
- ISO/IEC 14888-2:2008 Part 2: Integer factorization based mechanisms
- ISO/IEC 14888-3:2016 Part 3: Discrete logarithm based mechanisms
ISO 14889:2013 Ophthalmic optics – Spectacle lenses – Fundamental requirements for uncut finished lenses
ISO/TS 14904:2002 Road transport and traffic telematics – Electronic fee collection (EFC) – Interface specification for clearing between operators
ISO 14906:2011 Electronic fee collection – Application interface definition for dedicated short-range communication
ISO/TS 14907 Electronic fee collection – Test procedures for user and fixed equipment
- ISO/TS 14907-1:2015 Part 1: Description of test procedures
- ISO/TS 14907-2:2016 Part 2: Conformance test for the on-board unit application interface
ISO/IEC 14908 Information technology - Control network protocol
- ISO/IEC 14908-1:2012 Part 1: Protocol stack
- ISO/IEC 14908-2:2012 Part 2: Twisted pair communication
- ISO/IEC 14908-3:2012 Part 3: Power line channel specification
- ISO/IEC 14908-4:2012 Part 4: IP communication
ISO 14915 Software ergonomics for multimedia user interfaces
- ISO 14915-1:2002 Part 1: Design principles and framework
- ISO 14915-2:2003 Part 2: Multimedia navigation and control
- ISO 14915-3:2002 Part 3: Media selection and combination
ISO 14917:2017 Thermal spraying - Terminology, classification
ISO 14949:2001 Implants for surgery – Two-part addition-cure silicone elastomers
ISO 14963:2003 Mechanical vibration and shock – Guidelines for dynamic tests and investigations on bridges and viaducts
ISO 14971:2007 Medical devices – Application of risk management to medical devices
ISO 14972:1998 Sterile obturators for single use with over-needle peripheral intravascular catheters
ISO 14975:2000 Surface chemical analysis – Information formats
ISO 14976:1998 Surface chemical analysis – Data transfer format
ISO/IEC 14977:1996 Information technology – Syntactic metalanguage – Extended BNF
ISO 14978:2006 Geometrical product specifications (GPS) – General concepts and requirements for GPS measuring equipment
ISO 14982:1998 Agricultural and forestry machinery – Electromagnetic compatibility – Test methods and acceptance criteria

ISO 15000 – ISO 15999

ISO/TS 15000 Electronic business eXtensible Markup Language ebXML
- ISO 15000-5:2014 Part 5: Core Components Specification (CCS)
ISO 15001:2010 Anaesthetic and respiratory equipment – Compatibility with oxygen
ISO 15002:2008 Flow-metering devices for connection to terminal units of medical gas pipeline systems
ISO 15004 Ophthalmic instruments – Fundamental requirements and test methods
- ISO 15004-1:2006 Part 1: General requirements applicable to all ophthalmic instruments
- ISO 15004-2:2007 Part 2: Light hazard protection
ISO 15006:2011 Road vehicles – Ergonomic aspects of transport information and control systems – Specifications for in-vehicle auditory presentation
ISO 15010:1998 Disposable hanging devices for transfusion and infusion bottles – Requirements and test methods
ISO 15016:2015 Ships and marine technology - Guidelines for the assessment of speed and power performance by analysis of speed trial data
ISO/IEC 15018:2004 Information technology - Generic cabling for homes
ISO 15022 Securities – Scheme for messages (Data Field Dictionary)
ISO/IEC 15026 Systems and software engineering—Systems and software assurance
- ISO/IEC 15026-1:2013 Part 1: Concepts and vocabulary
- ISO/IEC 15026-2:2011 Part 2: Assurance case
- ISO/IEC 15026-3:2015 Part 3: System integrity levels
- ISO/IEC 15026-4:2012 Part 4: Assurance in the life cycle
ISO 15031 Road vehicles – Communication between vehicle and external equipment for emissions-related diagnostics
- ISO 15031-2:2010 Part 2: Guidance on terms, definitions, abbreviations and acronyms
ISO 15032:2000 Prostheses – Structural testing of hip units
ISO/IEC 15041:1997 Information technology - Data interchange on 90 mm optical disk cartridges - Capacity: 640 MB per cartridge
ISO/IEC TR 15044:2000 Information technology - Terminology for the Home Electronic System (HES)
ISO/IEC 15045 Information technology - Home Electronic System (HES) gateway
- ISO/IEC 15045-1:2004 Part 1: A residential gateway model for HES
- ISO/IEC 15045-2:2012 Part 2: Modularity and protocol
ISO/IEC 15049:1997 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Advice of charge supplementary services
ISO/IEC 15050:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Advice Of Charge supplementary services
ISO/IEC 15051:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Recall supplementary service
ISO/IEC 15052:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Recall supplementary service
ISO/IEC 15053:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Call Interception additional network feature
ISO/IEC 15054:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Call Interception additional network feature
ISO/IEC 15055:1997 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Transit counter additional network feature
ISO/IEC 15056:1997 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Transit counter additional network feature
ISO/IEC 15067 Information technology - Home Electronic System (HES) application model^{[Note 4]}
- ISO/IEC TR 15067-2:1997 Part 2: Lighting model for HES
- ISO/IEC 15067-3:2012 Part 3: Model of a demand-response energy management system for HES
- ISO/IEC TR 15067-3-2:2016 Part 3-2: GridWise interoperability context-setting framework
- ISO/IEC TR 15067-4:2001 Part 4: Security System for HES
ISO 15075:2003 Transport information and control systems – In-vehicle navigation systems – Communications message set requirements
ISO 15081:2011 Agricultural equipment - Graphical symbols for pressurized irrigation systems
ISO 15082 Road vehicles – Tests for rigid plastic safety glazing materials
ISO 15086 Hydraulic fluid power – Determination of the fluid-borne noise characteristics of components and systems
- ISO 15086-1:2001 Part 1: Introduction
- ISO 15086-2:2000 Part 2: Measurement of the speed of sound in a fluid in a pipe
- ISO 15086-3:2008 Part 3: Measurement of hydraulic impedance
ISO 15099 Thermal performance of windows, doors and shading devices – Detailed calculations
ISO 15112 Natural gas – Energy determination
ISO 15118 Road vehicles - Vehicle to grid communication interface
ISO 15137:2005 Self-adhesive hanging devices for infusion bottles and injection vials – Requirements and test methods
ISO 15142 Implants for surgery – Metal intramedullary nailing systems
- ISO 15142-1:2003 Part 1: Intramedullary nails
- ISO 15142-2:2003 Part 2: Locking components
- ISO 15142-3:2003 Part 3: Connection devices and reamer diameter measurements
ISO 15143 Earth-moving machinery and mobile road construction machinery – Worksite data exchange
- ISO 15143-1:2010 Part 1: System architecture
- ISO 15143-2:2010 Part 2: Data dictionary
- ISO/TS 15143-3:2016 Part 3: Telematics data
ISO/IEC 15145:1997 Information technology - Programming languages - FORTH
ISO/IEC 15149:2011 Information technology – Telecommunications and information exchange between systems – Magnetic field area network (MFAN)
- ISO/IEC 15149-1:2014 Part 1: Air interface
- ISO/IEC 15149-2:2015 Part 2: In-band Control Protocol for Wireless Power Transfer
- ISO/IEC 15149-3:2016 Part 3: Relay Protocol for Extended Range
- ISO/IEC 15149-4:2016 Part 4: Security Protocol for Authentication
ISO 15174:2012 Milk and milk products – Microbial coagulants – Determination of total milk-clotting activity
ISO 15188:2001 Project management guidelines for terminology standardization
ISO 15189:2012 Medical laboratories – Particular requirements for quality and competence
ISO/IEC 15200:1996 Information technology - Adaptive Lossless Data Compression algorithm (ALDC)
ISO/IEC 15205:2000 SBus - Chip and module interconnect bus
ISO 15212 Oscillation-type density meters
- ISO 15212-1:1998 Part 1: Laboratory instruments
- ISO 15212-2:2002 Part 2: Process instruments for homogeneous liquids
ISO 15213:2003 Microbiology of food and animal feeding stuffs – Horizontal method for the enumeration of sulfite-reducing bacteria growing under anaerobic conditions
ISO 15214:1998 Microbiology of food and animal feeding stuffs – Horizontal method for the enumeration of mesophilic lactic acid bacteria – Colony-count technique at 30 degrees C
ISO 15216 Microbiology of the food chain - Horizontal method for determination of hepatitis A virus and norovirus using real-time RT-PCR^{[Note 4]}
- ISO 15216-1:2017 Part 1: Method for quantification
- ISO/TS 15216-2:2013 Part 2: Method for qualitative detection
ISO 15223 Medical devices – Symbols to be used with medical device labels, labelling, and information to be supplied
- ISO 15223-1:2016 Part 1: General requirements
- ISO 15223-2:2010 Part 2: Symbol development, selection and validation
ISO 15225:2016 Medical devices – Quality management – Medical device nomenclature data structure
ISO 15226:1999 Technical product documentation – Life cycle model and allocation of documents
ISO 15230:2007 Mechanical vibration and shock – Coupling forces at the man–machine interface for hand-transmitted vibration
ISO/TR 15235:2001 Preparation of steel substrates before application of paints and related products - Collected information on the effect of levels of water-soluble salt contamination
ISO 15241:2012 Rolling bearings - Symbols for physical quantities
ISO 15253:2000 Ophthalmic optics and instruments – Optical devices for enhancing low vision
ISO 15254:2009 Ophthalmic optics and instruments – Electro-optical devices for enhancing low vision
ISO 15261:2004 Vibration and shock generating systems - Vocabulary
ISO/IEC TR 15285:1998 Information technology - An operational model for characters and glyphs
ISO/IEC 15286:1999 Information technology - 130 mm optical disk cartridges for information interchange - Capacity: 5.2 GB per cartridge
ISO/IEC/IEEE 15288:2015 Systems and software engineering – System life cycle processes
ISO/IEC/IEEE 15289:2017 Systems and software engineering – Content of life-cycle information items (documentation)
ISO/IEC 15291:1999 Information technology – Programming languages – Ada Semantic Interface Specification (ASIS)
ISO/IEC TR 15294:2000 Information technology – Methods for data flow control at synchronous and asynchronous DTE-DCE interfaces
ISO 15296:2004 Gas welding equipment - Vocabulary - Terms used for gas welding equipment
ISO/TR 15300:2001 Dentistry - Application of OSI clinical codification to the classification and coding of dental products
ISO/IEC 15307:1997 Information technology – Data interchange on 12.7 mm 128-track magnetic tape cartridges – DLT 4 format
ISO 15309:2013 Implants for surgery – Differential scanning calorimetry of poly ether ether ketone (PEEK) polymers and compounds for use in implantable medical devices
ISO/PAS 15339 Graphic technology - Printing from digital data across multiple technologies
- ISO/PAS 15339-1:2015 Part 1: Principles
- ISO/PAS 15339-2:2015 Part 2: Characterized reference printing conditions, CRPC1-CRPC7
ISO 15367 Lasers and laser-related equipment - Test methods for determination of the shape of a laser beam wavefront
- ISO 15367-1:2003 Part 1: Terminology and fundamental aspects
- ISO 15367-2:2005 Part 2: Shack-Hartmann sensors
ISO 15368:2001 Optics and optical instruments - Measurement of reflectance of plane surfaces and transmittance of plane parallel elements
ISO 15374:1998 Implants for surgery – Requirements for production of forgings
ISO 15375:2010 Medical infusion bottles – Suspension devices for multiple use – Requirements and test methods
ISO/TR 15377:2007 Measurement of fluid flow by means of pressure-differential devices – Guidelines for the specification of orifice plates, nozzles and Venturi tubes beyond the scope of ISO 5167
ISO 15378:2017 Primary packaging materials for medicinal products – Particular requirements for the application of ISO 9001:2015, with reference to good manufacturing practice (GMP)
ISO 15394:2009 Packaging - Bar code and two-dimensional symbols for shipping, transport and receiving labels
ISO 15403 Natural gas – Natural gas for use as a compressed fuel for vehicles
- ISO 15403-1:2006 Part 1: Designation of the quality
- ISO/TR 15403-2:2006 Part 2: Specification of the quality
ISO/IEC 15404:2000 Information technology – Office machines – Minimum information to be included in specification sheets – Facsimile equipment
ISO/IEC 15408 Information technology – Security techniques – Evaluation criteria for IT security
- ISO/IEC 15408-1:2009 Part 1: Introduction and general model
- ISO/IEC 15408-2:2008 Part 2: Security functional components
- ISO/IEC 15408-3:2008 Part 3: Security assurance components
ISO/IEC TR 15410:1998 Information technology – Telecommunications and information exchange between systems – PISN mobility-general principles and services aspects
ISO/IEC 15411:1999 Information technology - Segmented keyboard layouts
ISO/IEC 15412:1999 Information technology - Portable computer keyboard layouts
ISO/IEC TR 15413:2001 Information technology - Font services - Abstract service definition
ISO/IEC 15414:2015 Information technology - Open data processing - Reference Model - Enterprise Language
ISO/IEC 15415:2011 Information technology - Automatic identification and data capture techniques - Bar code symbol print quality test specification - Two-dimensional symbols
ISO/IEC 15416:2016 Automatic identification and data capture techniques - Bar code print quality test specification - Linear symbols
ISO/IEC 15417:2007 Information technology - Automatic identification and data capture techniques - Code 128 bar code symbology specification
ISO/IEC 15418:2016 Information technology - Automatic identification and data capture techniques - GS1 Application Identifiers and ASC MH10 Data Identifiers and maintenance
ISO/IEC 15419:2009 Information technology - Automatic identification and data capture techniques - Bar code digital imaging and printing performance testing
ISO/IEC 15420:2009 Information technology - Automatic identification and data capture techniques - EAN/UPC bar code symbology specification
ISO/IEC 15421:2010 Information technology - Automatic identification and data capture techniques - Bar code master test specifications
ISO/IEC 15423:2009 Information technology - Automatic identification and data capture techniques - Bar code scanner and decoder performance testing
ISO/IEC 15424:2008 Information technology - Automatic identification and data capture techniques - Data Carrier Identifiers (including Symbology Identifiers)
ISO/IEC 15426 Information technology - Automatic identification and data capture techniques - Bar code verifier conformance specification
- ISO/IEC 15426-1:2006 Part 1: Linear symbols
- ISO/IEC 15426-2:2015 Part 2: Two-dimensional symbols
ISO/IEC 15428:1999 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Wireless Terminal Location Registration supplementary service and Wireless Terminal Information Exchange additional network feature
ISO/IEC 15429:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Wireless Terminal Location Registration supplementary service and Wireless Terminal Information exchange additional network feature
ISO/IEC 15430:1999 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Wireless terminal call handling additional network features
ISO/IEC 15431:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Wireless terminal call handling additional network features
ISO/IEC 15432:1999 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Wireless Terminal Authentication supplementary services (WTAT and WTAN)
ISO/IEC 15433:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Wireless Terminal Authentication supplementary services
ISO/IEC 15434:2006 Information technology – Automatic identification and data capture techniques – Syntax for high-capacity ADC media
ISO/IEC 15437:2001 Information technology - Enhancements to LOTOS (E-LOTOS)
ISO/IEC 15438:2015 Information technology - Automatic identification and data capture techniques - PDF417 bar code symbology specification
ISO/IEC TR 15440:2016 Information technology - Future keyboards and other input devices and entry methods
ISO/IEC TR 15443 Information technology - Security techniques - Security assurance framework
- ISO/IEC TR 15443-1:2012 Part 1: Introduction and concepts
- ISO/IEC TR 15443-2:2012 Part 2: Analysis
ISO/IEC 15444 Information technology – JPEG 2000 image coding system
- ISO/IEC 15444-1:2016 Core coding system
- ISO/IEC 15444-2:2004 Extensions
- ISO/IEC 15444-3:2007 Motion JPEG 2000
- ISO/IEC 15444-4:2004 Conformance testing
- ISO/IEC 15444-5:2015 Reference software
- ISO/IEC 15444-6:2013 Part 6: Compound image file format
- ISO/IEC 15444-8:2007 Secure JPEG 2000
- ISO/IEC 15444-9:2005 Interactivity tools, APIs and protocols
- ISO/IEC 15444-10:2011 Extensions for three-dimensional data
- ISO/IEC 15444-11:2007 Wireless
- ISO/IEC 15444-12:2015 Part 12: ISO base media file format [Withdrawn, no replacement]
- ISO/IEC 15444-13:2008 An entry level JPEG 2000 encoder
- ISO/IEC 15444-14:2013 Part 14: XML representation and reference
ISO/IEC 15445:2000 Information technology – Document description and processing languages – HyperText Markup Language (HTML)
ISO/IEC TR 15446:2009 Information technology - Security techniques - Guide for the production of Protection Profiles and Security Targets
ISO/IEC 15457 Identification cards – Thin flexible cards
- ISO/IEC 15457-1:2008 Part 1: Physical characteristics
- ISO/IEC 15457-2:2007 Part 2: Magnetic recording technique
- ISO/IEC 15457-3:2008 Part 3: Test methods
ISO/IEC 15459 Information technology - Automatic identification and data capture techniques - Unique identification
- ISO/IEC 15459-1:2014 Part 1: Individual transport units
- ISO/IEC 15459-2:2015 Part 2: Registration procedures
- ISO/IEC 15459-3:2014 Part 3: Common rules
- ISO/IEC 15459-4:2014 Part 4: Individual products and product packages
- ISO/IEC 15459-5:2014 Part 5: Individual returnable transport items (RTIs)
- ISO/IEC 15459-6:2014 Part 6: Groupings
ISO 15469:2004 Spatial distribution of daylight – CIE standard general sky
ISO/IEC 15474 Information technology - CDIF framework
- ISO/IEC 15474-1:2002 Part 1: Overview
- ISO/IEC 15474-2:2002 Part 2: Modelling and extensibility
ISO/IEC 15475 Information technology - CDIF transfer format
- ISO/IEC 15475-1:2002 Part 1: General rules for syntaxes and encodings
- ISO/IEC 15475-2:2002 Part 2: Syntax SYNTAX.1
- ISO/IEC 15475-3:2002 Part 3: Encoding ENCODING.1
ISO/IEC 15476 Information technology - CDIF semantic metamodel
- ISO/IEC 15476-1:2002 Part 1: Foundation
- ISO/IEC 15476-2:2002 Part 2: Common
- ISO/IEC 15476-3:2006 Part 3: Data definitions
- ISO/IEC 15476-4:2005 Part 4: Data models
- ISO/IEC 15476-6:2006 Part 6: State/event models
ISO 15480:2019 Fasteners — Hexagon washer head drilling screws with tapping screw thread
ISO 15481:1999 Cross recessed pan head drilling screws with tapping screw thread
ISO 15482:1999 Cross recessed countersunk head drilling screws with tapping screw thread
ISO 15483:1999 Cross recessed raised countersunk head drilling screws with tapping screw thread
ISO/IEC 15485:1997 Information technology - Data interchange on 120 mm optical disk cartridges using phase change PD format - Capacity: 650 MB per cartridge
ISO/IEC 15486:1998 Information technology - Data interchange on 130 mm optical disk cartridges of type WORM (Write Once Read Many) using irreversible effects - Capacity: 2.6 GB per cartridge
ISO 15489 Information and documentation – Records management
- ISO 15489-1:2016 Part 1: Concepts and principles
- ISO/TR 15489-2:2001 Part 2: Guidelines [Withdrawn, no replacement]
ISO/IEC 15498:1997 Information technology - Data interchange on 90 mm optical disk cartridges - HS-1 format - Capacity: 650 MB per cartridge
ISO/IEC 15504 Information technology – Process assessment
ISO/IEC 15505:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Message Waiting Indication supplementary service
ISO/IEC 15506:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Message Waiting Indication supplementary service
ISO/IEC 15507:1997 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – PINX clock synchronization
ISO 15511:2011 Information and documentation - International standard identifier for libraries and related organizations (ISIL)
ISO 15519 Specification for diagrams for process industry
- ISO 15519-1:2010 Part 1: General rules
- ISO 15519-2:2015 Part 2: Measurement and control
ISO/IEC 15521:1998 Information technology – 3.81 mm wide magnetic tape cartridge for information interchange – Helical scan recording – DDS-3 format using 125 m length tapes
ISO 15529:2010 Optics and photonics - Optical transfer function - Principles of measurement of modulation transfer function (MTF) of sampled imaging systems
ISO 15530 Geometrical product specifications (GPS) – Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement
- ISO/TS 15530-1:2013 Part 1: Overview and metrological characteristics
- ISO 15530-3:2011 Part 3: Use of calibrated workpieces or measurement standards
- ISO/TS 15530-4:2008 Part 4: Evaluating task-specific measurement uncertainty using simulation
ISO 15553:2006 Water quality – Isolation and identification of Cryptosporidium oocysts and Giardia cysts from water
ISO 15583:2005 Ships and marine technology - Maritime standards list
ISO/TR 15599:2002 Digital codification of dental laboratory procedures
ISO 15614 Specification and qualification of welding procedures for metallic materials – Welding procedure test
ISO 15622:2010 Intelligent transport systems – Adaptive Cruise Control systems – Performance requirements and test procedures
ISO 15623:2013 Intelligent transport systems – Forward vehicle collision warning systems – Performance requirements and test procedures
ISO/TS 15624:2001 Transport information and control systems – Traffic Impediment Warning Systems (TIWS) – System requirements
ISO 15628:2013 Intelligent transport systems – Dedicated short range communication (DSRC) – DSRC application layer
ISO 15638 Intelligent transport systems – Framework for cooperative telematics applications for regulated commercial freight vehicles (TARV)^{[Note 4]}
- ISO 15638-1:2012 Part 1: Framework and architecture
- ISO 15638-2:2013 Part 2: Common platform parameters using CALM
- ISO 15638-3:2013 Part 3: Operating requirements, 'Approval Authority' procedures, and enforcement provisions for the providers of regulated services
- ISO 15638-5:2013 Part 5: Generic vehicle information
- ISO 15638-6:2014 Part 6: Regulated applications
- ISO 15638-7:2013 Part 7: Other applications
- ISO 15638-8:2014 Part 8: Vehicle access management
- ISO/TS 15638-9:2013 Part 9: Remote electronic tachograph monitoring (RTM)
- ISO 15638-10:2017 Part 10: Emergency messaging system/eCall
- ISO 15638-11:2014 Part 11: Driver work records
- ISO 15638-12:2014 Part 12: Vehicle mass monitoring
- ISO/TS 15638-13:2015 Part 13: "Mass" information for jurisdictional control and enforcement
- ISO 15638-14:2014 Part 14: Vehicle access control
- ISO 15638-15:2014 Part 15: Vehicle location monitoring
- ISO 15638-16:2014 Part 16: Vehicle speed monitoring
- ISO 15638-17:2014 Part 17: Consignment and location monitoring
- ISO 15638-18:2017 Part 18: ADR (Dangerous Goods)
- ISO/TS 15638-19:2013 Part 19: Vehicle parking facilities (VPF)
ISO 15642:2003 Road construction and maintenance equipment – Asphalt mixing plants – Terminology and commercial specifications
ISO 15662:2006 Intelligent transport systems – Wide area communication – Protocol management information
ISO 15664:2001 Acoustics – Noise control design procedures for open plant
ISO 15665:2003 Acoustics – Acoustic insulation for pipes, valves and flanges
ISO 15667:2000 Acoustics – Guidelines for noise control by enclosures and cabins
ISO 15674:2016 Cardiovascular implants and artificial organs – Hard-shell cardiotomy/venous reservoir systems (with/without filter) and soft venous reservoir bags
ISO 15675:2016 Cardiovascular implants and artificial organs – Cardiopulmonary bypass systems – Arterial blood line filters
ISO 15676:2016 Cardiovascular implants and artificial organs – Requirements for single-use tubing packs for cardiopulmonary bypass and extracorporeal membrane oxygenation (ECMO)
ISO 15686 Buildings and constructed assets – Service life planning
ISO 15688:2012 Road construction and maintenance equipment – Soil stabilizers – Terminology and commercial specifications
ISO 15689:2003 Road construction and maintenance equipment – Powder binder spreaders – Terminology and commercial specifications
ISO/IEC 15693 Identification cards – Contactless integrated circuit cards – Vicinity cards
ISO/TS 15696:2012 Cranes – List of equivalent terms
ISO 15706 Information and documentation – International Standard Audiovisual Number (ISAN)
ISO 15707:2001 Information and documentation – International Standard Musical Work Code (ISWC)
ISO/IEC 15718:1998 Information technology – Data interchange on 8 mm wide magnetic tape cartridge – Helical scan recording – HH-1 format
ISO/IEC 15731:1998 Information technology – 12.65 mm wide magnetic tape cassette for information interchange – Helical scan recording – DTF-1 format
ISO 15744:2002 Hand-held non-electric power tools – Noise measurement code – Engineering method (grade 2)
ISO 15747:2010 Plastic containers for intravenous injections
ISO 15752:2010 Ophthalmic instruments – Endoilluminators – Fundamental requirements and test methods for optical radiation safety
ISO/IEC 15757:1998 Information technology – Data interchange on 8 mm wide magnetic tape cartridge – Helical scan recording – DA-2 format
ISO 15759:2005 Medical infusion equipment – Plastics caps with inserted elastomeric liner for containers manufactured by the blow-fill-seal (BFS) process
ISO/TS 15768:2000 Measurement of liquid velocity in open channels – Design, selection and use of electromagnetic current meters
ISO 15769:2010 Hydrometry – Guidelines for the application of acoustic velocity meters using the Doppler and echo correlation methods
ISO/IEC 15771:1998 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Common information additional network feature
ISO/IEC 15772:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Common Information additional network feature
ISO/IEC 15773:1998 Information technology – Telecommunications and information exchange between systems – Broadband Private Integrated Services Network – Inter-exchange signalling protocol – Transit counter additional network feature
ISO/IEC 15776:2001 VME64bus - Specification
ISO/IEC 15780:1998 Information technology – 8 mm wide magnetic tape cartridge – Helical scan recording – AIT-1 format
ISO 15782 Certificate management for financial services^{[Note 4]}
- ISO 15782-1:2009 Part 1: Public key certificates
- ISO 15782-2:2001 Part 2: Certificate extensions
ISO 15783:2002 Seal-less rotodynamic pumps – Class II – Specification
ISO 15784 Intelligent transport systems (ITS) – Data exchange involving roadside modules communication
- ISO 15784-1:2008 Part 1: General principles and documentation framework of application profiles
- ISO 15784-2:2015 Part 2: Centre to field device communications using SNMP
- ISO 15784-3:2008 Part 3: Application profile-data exchange (AP-DATEX)
ISO 15785:2002 Technical drawings – Symbolic presentation and indication of adhesive, fold and pressed joints
ISO 15786:2008 Technical drawings – Simplified representation and dimensioning of holes
ISO 15787:2016 Technical product documentation – Heat-treated ferrous parts – Presentation and indications
ISO 15798:2013 Ophthalmic implants – Ophthalmic viscosurgical devices
ISO/IEC 15802 Information technology – Telecommunications and information exchange between systems – Local and metropolitan area networks – Common specifications
- ISO/IEC 15802-1:1995 Part 1: Medium Access Control (MAC) service definition
- ISO/IEC 15802-3:1998 Part 3: Media Access Control (MAC) Bridges
ISO/IEC 15816:2002 Information technology - Security techniques - Security information objects for access control
ISO 15836:2009 Information and documentation – The Dublin Core metadata element set
- ISO 15836-1:2017 Part 1: Core elements
ISO/TR 15847:2008 Graphic technology - Graphical symbols for printing press systems and finishing systems, including related auxiliary equipment
ISO 15849:2001 Ships and marine technology – Guidelines for implementation of a fleet management system network
ISO/IEC 15851:1999 Information technology - Communication protocol - Open MUMPS Interconnect
ISO/IEC 15852:1999 Information technology - Programming languages - M Windowing API
ISO 15867:2003 Intermediate bulk containers (IBCs) for non-dangerous goods – Terminology
ISO 15870:2000 Powered industrial trucks - Safety signs and hazard pictorials - General principles
ISO 15878:2008 Road construction and maintenance equipment – Asphalt pavers – Terminology and commercial specifications
ISO/IEC 15895:1999 Information technology – Data interchange on 12.7 mm 128-track magnetic tape cartridges – DLT 3-XT format
ISO/IEC 15896:1999 Information technology – Data interchange on 12.7 mm 208-track magnetic tape cartridges – DLT 5 format
ISO/IEC 15897:2011 Information technology - User interfaces - Procedures for the registration of cultural elements
ISO 15883-1:2006 specifies general performance requirements for washer-disinfectors (WD) and their accessories that are intended to be used for cleaning and disinfection of re-usable medical devices and other articles used in the context of medical, dental, pharmaceutical and veterinary practice.
ISO/IEC 15898:1998 Information technology - Data interchange on 356 mm optical disk cartridges - WORM, using phase change technology - Capacity: 14.8 GB and 25 GB per cartridge
ISO/IEC 15899:1998 Information technology – Telecommunications and information exchange between systems – Broadband Private Integrated Services Network – Service description – Broadband connection oriented bearer services
ISO 15901-2:2022 Pore size distribution and porosity of solid materials by mercury porosimetry and gas adsorption — Part 2: Analysis of nanopores by gas adsorption
ISO 15902:2004 Optics and photonics - Diffractive optics - Vocabulary
ISO/IEC 15909 Systems and software engineering - High-level Petri nets
- ISO/IEC 15909-1:2004 Part 1: Concepts, definitions and graphical notation
- ISO/IEC 15909-2:2011 Part 2: Transfer format
ISO 15919:2001 Information and documentation - Transliteration of Devanagari and related Indic scripts into Latin characters
ISO 15924:2004 Information and documentation – Codes for the representation of names of scripts
ISO 15926 - Integration of Life-cycle Data for Process Plants including Oil and Gas Production Facilities
ISO 15927 Hygrothermal performance of buildings – Calculation and presentation of climatic data
- ISO 15927-1:2003 Part 1: Monthly means of single meteorological elements
- ISO 15927-2:2009 Part 2: Hourly data for design cooling load
- ISO 15927-3:2009 Part 3: Calculation of a driving rain index for vertical surfaces from hourly wind and rain data
- ISO 15927-4:2005 Part 4: Hourly data for assessing the annual energy use for heating and cooling
- ISO 15927-5:2004 Part 5: Data for design heat load for space heating
- ISO 15927-6:2007 Part 6: Accumulated temperature differences (degree-days)
ISO 15930 Graphic technology – Prepress digital data exchange using PDF^{[Note 4]}
ISO 15932:2013 Microbeam analysis - Analytical electron microscopy - Vocabulary
ISO/IEC 15938 Information technology - Multimedia content description interface
ISO/IEC/IEEE 15939:2017 Systems and software engineering - Measurement process
ISO/IEC 15940:2013 Systems and software engineering - Software Engineering Environment Services
ISO/IEC TR 15942:2000 Information technology - Programming languages - Guide for the use of the Ada programming language in high integrity systems
ISO/IEC 15944 Information technology - Business operational view
- ISO/IEC 15944-1:2011 Part 1: Operational aspects of open-edi for implementation
- ISO/IEC 15944-2:2015 Part 2: Registration of scenarios and their components as business objects
- ISO/IEC 15944-4:2015 Part 4: Business transaction scenarios – Accounting and economic ontology
- ISO/IEC 15944-5:2008 Part 5: Identification and referencing of requirements of jurisdictional domains as sources of external constraints
- ISO/IEC TR 15944-6:2015 Part 6: Technical introduction to e-Business modelling
- ISO/IEC 15944-7:2009 Part 7: eBusiness vocabulary
- ISO/IEC 15944-8:2012 Part 8: Identification of privacy protection requirements as external constraints on business transactions
- ISO/IEC 15944-9:2015 Part 9: Business transaction traceability framework for commitment exchange
- ISO/IEC 15944-10:2013 Part 10: IT-enabled coded domains as semantic components in business transactions
- ISO/IEC 15944-20:2015 Part 20: Linking business operational view to functional service view
ISO/IEC 15945:2002 Information technology - Security techniques - Specification of TTP services to support the application of digital signatures
ISO/IEC 15946 Information technology - Security techniques - Cryptographic techniques based on elliptic curves
- ISO/IEC 15946-1:2016 Part 1: General
- ISO/IEC 15946-5:2017 Part 5: Elliptic curve generation
ISO/IEC 15948 Information technology – Computer graphics and image processing – Portable Network Graphics (PNG): Functional specification
ISO/IEC 15953:1999 Information technology – Open Systems Interconnection – Service definition for the Application Service Object Association Control Service Element
ISO/IEC 15954:1999 Information technology – Open Systems Interconnection – Connection-mode protocol for the Application Service Object Association Control Service Element
ISO/IEC 15955:1999 Information technology – Open Systems Interconnection – Connectionless protocol for the Application Service Object Association Control Service Element
ISO/IEC 15961 Information technology - Radio frequency identification (RFID) for item management: Data protocol
- ISO/IEC 15961-1:2013 Part 1: Application interface
- ISO/IEC 15961-4:2016 Part 4: Application interface commands for battery assist and sensor functionality
ISO/IEC 15962:2013 Information technology - Radio frequency identification (RFID) for item management - Data protocol: data encoding rules and logical memory functions
ISO/IEC 15963:2009 Information technology - Radio frequency identification for item management - Unique identification for RF tags
ISO 15970 Natural gas – Measurement of properties – Volumetric properties: density, pressure, temperature and compression factor
ISO 15971:2008 Natural gas – Measurement of properties – Calorific value and Wobbe index
ISO 15985:2004 Plastics – Determination of the ultimate anaerobic biodegradation and disintegration under high-solids anaerobic-digestion conditions – Method by analysis of released biogas
ISO/IEC 15991:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Call Priority Interruption and Call Priority Interruption Protection supplementary services
ISO/IEC 15992:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Call Priority Interruption and Call Priority Interruption Protection supplementary services

Notes

^ This list generally excludes draft versions.
^ ISO deliverables include "specifications" (ISO/PAS, ISO/TS), "reports" (ISO/TR), etc, which are not referred to by ISO as "standards".
^ ^a ^b ^c The exact wording of this title varies between parts. This is the wording of the most recently published part.
^ ^a ^b ^c ^d ^e The exact wording of this title varies between parts. This is the wording of the most recently published part.

References

^ "Standards catalogue". ISO.
^ "Freely Available Standards". ISO.
^ European Standards, ISO 14045, accessed 2 August 2023

External links

[1] This list generally excludes draft versions.

[2] ISO deliverables include "specifications" (ISO/PAS, ISO/TS), "reports" (ISO/TR), etc, which are not referred to by ISO as "standards".

[VariesBetweenParts-6] The exact wording of this title varies between parts. This is the wording of the most recently published part.

[VariesBetweenParts2-7] The exact wording of this title varies between parts. This is the wording of the most recently published part.

[3] "Standards catalogue". ISO.

[4] "Freely Available Standards". ISO.

[5] European Standards, ISO 14045, accessed 2 August 2023

[Note 1]

[Note 2]

[1]

[2]

[3]

[Note 3]

[Note 4]