South African Class 14C 4-8-2, 1st batch

The South African Railways Class 14C 4-8-2 of 1918 was a steam locomotive.

South African Class 14C, 14CB, 14CR & 14CRB 4-8-2, 1st batch
No. 1766, as built with a Belpaire firebox, c. 1930
Type and origin
♠ Class 14C, standard, as built with a Belpaire firebox
Class 14CB, rebalanced for branchline working
Class 14CR, standard, Watson Standard boiler
Class 14CRB, branchline, Watson Standard boiler
ʘ 22 in (559 mm) bore - ʘ 21+34 in (552 mm) bore
Power typeSteam
DesignerMontreal Locomotive Works
BuilderMontreal Locomotive Works
Serial number58637-58656
ModelClass 14C
Build date1918-1919
Total produced20
Specifications
Configuration:
 • Whyte4-8-2 (Mountain)
 • UIC2'D1'h2
Driver2nd coupled axle
Gauge3 ft 6 in (1,067 mm) Cape gauge
Leading dia.28+12 in (724 mm)
Coupled dia.48 in (1,219 mm)
Trailing dia.33 in (838 mm)
Tender wheels34 in (864 mm)
Wheelbase59 ft 14 in (17,990 mm) ​
 • Engine30 ft 8 in (9,347 mm)
 • Leading6 ft 2 in (1,880 mm)
 • Coupled12 ft 9 in (3,886 mm)
 • Tender17 ft 11 in (5,461 mm)
 • Tender bogie4 ft 7 in (1,397 mm)
Length:
 • Over couplers66 ft 10+18 in (20,374 mm)
Height 12 ft 9+38 in (3,896 mm)
13 ft 34 in (3,981 mm)
Frame typeBar
Axle load♠ 15 LT 16 cwt (16,050 kg)
14 LT 16 cwt (15,040 kg)
16 LT 15 cwt (17,020 kg)
14 LT 17 cwt (15,090 kg) ​
 • Leading♠ 14 LT 8 cwt (14,630 kg)
14 LT 6 cwt (14,530 kg)
16 LT 2 cwt (16,360 kg)
14 LT 8 cwt (14,630 kg)
 • 1st coupled♠ 15 LT 10 cwt (15,750 kg)
14 LT 16 cwt (15,040 kg)
16 LT 8 cwt (16,660 kg)
14 LT 17 cwt (15,090 kg)
 • 2nd coupled♠ 14 LT 19 cwt (15,190 kg)
14 LT 14 cwt (14,940 kg)
15 LT 15 cwt (16,000 kg)
14 LT 14 cwt (14,940 kg)
 • 3rd coupled♠ 15 LT 12 cwt (15,850 kg)
14 LT 14 cwt (14,940 kg)
16 LT 10 cwt (16,760 kg)
14 LT 15 cwt (14,990 kg)
 • 4th coupled♠ 15 LT 16 cwt (16,050 kg)
14 LT 16 cwt (15,040 kg)
16 LT 15 cwt (17,020 kg)
14 LT 17 cwt (15,090 kg)
 • Trailing♠ 8 LT 12 cwt (8,738 kg)
10 LT 1 cwt (10,210 kg)
9 LT 1 cwt (9,195 kg)
10 LT 1 cwt (10,210 kg)
 • Tender axle12 LT 14 cwt 2 qtr (12,930 kg) av.
Adhesive weight♠ 61 LT 17 cwt (62,840 kg)
59 LT (59,950 kg)
65 LT 8 cwt (66,450 kg)
59 LT 3 cwt (60,100 kg)
Loco weight♠ 84 LT 17 cwt (86,210 kg)
83 LT 7 cwt (84,690 kg)
90 LT 11 cwt (92,000 kg)
83 LT 12 cwt (84,940 kg)
Tender weight50 LT 18 cwt (51,720 kg)
Total weight♠ 135 LT 15 cwt (137,900 kg)
134 LT 5 cwt (136,400 kg)
141 LT 9 cwt (143,700 kg)
134 LT 10 cwt (136,700 kg)
Tender typeLP (2-axle bogies)
Fuel typeCoal
Fuel capacity10 LT (10.2 t)
Water cap.4,250 imp gal (19,300 L)
Firebox:
 • Type Belpaire
Round-top
 • Grate area 37 sq ft (3.437 m2)
Boiler:
 • Model Watson Standard no. 2
 • Pitch 7 ft 7 in (2,311 mm)
8 ft 1+12 in (2,476 mm)
 • Diameter 5 ft 7+12 in (1,714 mm)
 • Tube plates 19 ft 38 in (5,801 mm)
19 ft 4 in (5,893 mm) steel
19 ft 3+58 in (5,883 mm) copper
 • Small tubes 139: 2+14 in (57 mm)
87: 2+12 in (64 mm)
 • Large tubes 24: 5+12 in (140 mm)
30: 5+12 in (140 mm)
Boiler pressureʘ 190 psi (1,310 kPa)
ʘ 195 psi (1,344 kPa)
ʘ 180 psi (1,241 kPa)
ʘ 183 psi (1,262 kPa)
Safety valve Ramsbottom
Pop
Heating surface:
 • Firebox 138 sq ft (12.8 m2)
142 sq ft (13.2 m2)
 • Tubes 2,212 sq ft (205.5 m2)
1,933 sq ft (179.6 m2)
 • Total surface 2,350 sq ft (218 m2)
2,075 sq ft (192.8 m2)
Superheater:
 • Heating area 526 sq ft (48.9 m2)
492 sq ft (45.7 m2)
CylindersTwo
Cylinder size 22 in (559 mm) bore
21+34 in (552 mm) bore
26 in (660 mm) stroke
Valve gearWalschaerts
Valve typePiston
CouplersJohnston link-and-pin
AAR knuckle (1930s)
Performance figures
Tractive effortʘ 37,360 lbf (166.2 kN) @ 75%
ʘ 37,480 lbf (166.7 kN) @ 75%
ʘ 35,400 lbf (157 kN) @ 75%
ʘ 35,980 lbf (160.0 kN) @ 75%
ʘ 35,170 lbf (156.4 kN) @ 75%
Career
OperatorsSouth African Railways
ClassClass 14C, 14CB, 14CR, 14CRB
Number in class20
Numbers1761-1780
Delivered1918-1919
First run1918
Withdrawn1980s
The leading coupled axle had flangeless wheels

In 1918 and 1919, the South African Railways placed the first batch of twenty Class 14C steam locomotives with a 4-8-2 Mountain type wheel arrangement in service. Three more batches were acquired between 1919 and 1922, each with a different maximum axle loading, to bring the total in the class to 73. Through reboilerings, rebalancings and cylinder bushings during its service life, this single class eventually ended up as six distinct locomotive classes with two boiler types and a multitude of axle load and boiler pressure configurations.[1][2][3][4][5]

Manufacturer

edit

As a result of wartime disruption in Europe and Britain, the fourth version of the Class 14 locomotive was ordered from the Montreal Locomotive Works (MLW) in Canada in 1918. It was designated Class 14C and the first batch of twenty was delivered in 1918 and early in 1919, numbered in the range from 1761 to 1780.[1][2]

Until 1922, three more batches of Class 14C would follow from the same manufacturer. All four batches differed in terms of maximum axle loading, adhesive weight and engine weight.[1][3][4]

Characteristics

edit

While these locomotives were built to the specifications of D.A. Hendrie, at the time the Chief Mechanical Engineer (CME) of the South African Railways (SAR), they were designed by the Canadian manufacturer and the result was a locomotive with some typical North American characteristics. They had large cabs, bar frames, Walschaerts valve gear, Belpaire fireboxes and were superheated.[1][5][6]

A prominent distinction from the earlier Classes 14, 14A and 14B locomotives was their American style high running boards. It had an even better cylinder design than the Class 14, with larger and straighter ports which resulted in a very sharp, free exhaust.[1][5][6]

All four batches were delivered with Type LP tenders, with a coal capacity of 10 long tons (10.2 tonnes) and a water capacity of 4,250 imperial gallons (19,300 litres).[3][4]

Modifications and reclassifications

edit

The Class 14C proved to be good locomotives, even though they initially suffered from some rather bad teething troubles. Once these were rectified, they went on to become fine performers which were associated with hard work all through their service lives.[1][2][5]

During 1920, most of the fireboxes on the early orders of the Class 14C were restayed. The reversing gear was of the single cylinder type and tended to creep. Hendrie therefore fitted oil cylinders and installed his Hendrie reversing gear, which was manufactured in the Pretoria workshops during 1922. Modifications were also made to the finger bars and rocking grate cylinders of the firebox and to the sanding gear. Approximately 2 long tons (2.0 tonnes) of lead were run into the smokebox saddle casting to provide additional weight on the leading bogie.[2]

Watson Standard boilers

edit

During the 1930s, many serving locomotives were reboilered with a standard boiler type designed by A.G. Watson, CME of the SAR at the time, as part of his standardisation policy. Such Watson Standard reboilered locomotives were reclassified by adding an "R" suffix to their classification.[3][4][5]

All twenty locomotives were eventually reboilered with Watson Standard no. 2 boilers and reclassified to Class 14CR. Only slight alterations were necessary to the engine frames. In the process, the boiler pitch was raised from 7 feet 7 inches (2,311 millimetres) to 8 feet 1+12 inches (2,476 millimetres), which raised the chimney height from 12 feet 9+38 inches (3,896 millimetres) to 13 feet 34 inch (3,981 millimetres) and exceeded the loading gauge height of 13 feet (3,962 millimetres) above the railhead. The only other engine on which reboilering resulted in the exceeding of the height restriction was the Class 15BR.[2]

The reboilered engines were also equipped with Watson cabs with their distinctive slanted fronts, compared to the conventional vertical fronts of their original cabs. Early conversions were equipped with copper and later conversions with steel fireboxes. Three of them, numbers 1762 to 1764, would not undergo further modifications and would retain the Class 14CR designation.[2][3][4]

Their original Belpaire boilers were fitted with Ramsbottom safety valves, while the Watson Standard boiler was fitted with Pop safety valves. An obvious difference between an original and a Watson Standard reboilered locomotive is usually a rectangular regulator cover, just to the rear of the chimney on the reboilered locomotive. In the case of the Class 14C, two even more obvious differences were the Watson cab and the absence of the Belpaire firebox hump between the cab and boiler on the reboilered locomotives.[3][4]

Rebalancing

edit

Around 1930, the question of maximum axle loads for locomotives was thoroughly investigated by the Mechanical and Civil Engineering Departments of the SAR. It was found that, among some other locomotives, the Class 14C had a rather severe vertical hammer blow effect on the track when running at speed due to an undue proportion of the reciprocating parts being balanced. Modifications were accordingly made to the Class 14C to allow some of them to run on 60 pounds per yard (30 kilograms per metre) track.[2]

The locomotives had weights attached between the frames to increase adhesion. Over time, most of the Class 14C family of locomotives were "rebalanced" by having these weights increased or reduced to redistribute, increase or reduce the axle loading and adhesive weight by altering the loads on the individual coupled wheels, leading bogies and trailing pony trucks. Coupled wheel axle loading adjustment was achieved by attaching steel boxes, filled with an appropriate amount of lead, over each axle between the frames. Their boiler pressure setting was reduced from 190 to 180 pounds per square inch (1,310 to 1,241 kilopascals).[3][4][6]

The lighter version of the rebalanced locomotives was reclassified to Class 14CB, with the "B" indicating branch line service. Those which had also been reboilered with Watson Standard no. 2 boilers were reclassified to Class 14CRB.[3][4][6]

Cylinder bushing

edit

Several of the locomotives had their cylinders bushed to reduce the bore from the as-built 22 to 21+34 inches (559 to 552 millimetres). At the same time the boiler pressure setting of the Classes 14C and 14CR locomotives was adjusted upwards from 190 to 195 pounds per square inch (1,310 to 1,344 kilopascals) to keep their tractive effort more or less unaffected by the reduction in piston diameter. The boiler pressure setting of the branchline Classes 14CB and 14CRB was adjusted upwards from 180 to 183 pounds per square inch (1,241 to 1,262 kilopascals).[2][3][4]

Service

edit

South African Railways

edit

The Class 14C was placed in service on the Cape Eastern system, working the Umtata branch into Transkei and on the mainline to Cookhouse. Some went to the Cape Western system, where they banked up the Hex River Pass from De Doorns and later worked with Class 19C locomotives across Sir Lowry's Pass to Caledon and Bredasdorp in the Overberg. A few were also used on the Cape Midland system, in Natal and the Eastern Transvaal.[5]

In their later years, many of these locomotives remained on the Cape Western system, most being shedded at Paardeneiland in Cape Town and at Beaufort West, and one at De Aar, where they were mostly used as shunting engines and on short local pick-ups. A large number were also used on the Cape Eastern system, shedded at East London and used as shunting engines, on local pick-ups and also in suburban service. A few also served their last years in the Eastern Transvaal, shedded at Pietersburg and Witbank.[6]

Other operators

edit

Between 1918 and 1921, the Rhodesia Railways (RR) purchased a slightly lighter version of the original Class 14C from MLW. These were designated the RR Class 11. A further batch was built in 1948 and designated RR Class 11A. Some of the RR Class 11s and all the RR Class 11As were eventually sold to Caminhos de Ferro de Moçambique (CFM) and were utilised on the line between Mozambique and Swaziland (since 2018 renamed to Eswatini).[6]

Works numbers

edit

The table lists their years built, manufacturer's works numbers, engine numbers and eventual classifications.[3][4]


Preservation

edit
Number Works nmr THF / Private Leaselend / Owner Current Location Outside South Africa ?
1771 Private Krugersdorp Locomotive Depot
1778 Private Queenstown Locomotive Depot
2010 Private Municipality Ashton (Main Street)

Illustration

edit

References

edit
  1. ^ a b c d e f Holland, D. F. (1972). Steam Locomotives of the South African Railways. Vol. 2: 1910-1955 (1st ed.). Newton Abbott, England: David & Charles. pp. 34–36, 83–84. ISBN 978-0-7153-5427-8.
  2. ^ a b c d e f g h Espitalier, T.J.; Day, W.A.J. (1945). The Locomotive in South Africa - A Brief History of Railway Development. Chapter VII - South African Railways (Continued). South African Railways and Harbours Magazine, September 1945. pp. 675-676.
  3. ^ a b c d e f g h i j South African Railways & Harbours/Suid Afrikaanse Spoorweë en Hawens (15 Aug 1941). Locomotive Diagram Book/Lokomotiefdiagramboek, 3'6" Gauge/Spoorwydte. SAR/SAS Mechanical Department/Werktuigkundige Dept. Drawing Office/Tekenkantoor, Pretoria. p. 43.
  4. ^ a b c d e f g h i j South African Railways & Harbours/Suid Afrikaanse Spoorweë en Hawens (15 Aug 1941). Locomotive Diagram Book/Lokomotiefdiagramboek, 2'0" & 3'6" Gauge/Spoorwydte, Steam Locomotives/Stoomlokomotiewe. SAR/SAS Mechanical Department/Werktuigkundige Dept. Drawing Office/Tekenkantoor, Pretoria. pp. 6a-7a, 41, 43.
  5. ^ a b c d e f Paxton, Leith; Bourne, David (1985). Locomotives of the South African Railways (1st ed.). Cape Town: Struik. pp. 10–11, 58–59. ISBN 0869772112.
  6. ^ a b c d e f Durrant, AE (1989). Twilight of South African Steam (1st ed.). Newton Abbott: David & Charles. pp. 81–82. ISBN 0715386387.