Talk:Thermal diffusivity

Untitled

Does anyone have a link to a table of mass diffussivity coefficients? Kelly is a dreamboat. <3

redirect appropriateness

There's apparently at least 3 kinds of diffusivity, including thermal, mass, and momentum. I'm thinking thermal shouldn't get a monopoly on the subject. (I don't have the expertise to be sure). Ojcit 17:21, 2 October 2006 (UTC)

Reply: I agree, it seems a bit strange that diffusivity redirects here, since in my experience the term normally refers to mass diffusion, and this quantity would typically be referred to as the thermal conductivity.

explanation

I think it is a measure for how fast the heat (or actually the standard deviation of the heat) spreads from a certain point, shouldn't this be mentioned somewhere? (Unsigned)

It is a measure for how fast temperature (in Kelvin) spreads within a certain material at a given temperature. The heat (in Joule) spreading measure is actually thermal conductivity. E.g. copper has a higher thermal conductivity but a the smaller thermal diffusivity than gold , i.e. copper can transport the same amount of heat faster than gold, but heats up less. Nontheless, I agree with the idea of adding a non-academic discriptive explanation. Filousoph (talk) 05:34, 14 May 2012 (UTC)

In particular the thermal diffusivity is in my view not "how cold a material feels", as written in the introduction. If I take a material with very high diffusivity but low density and low cp, it will not feel cold since the low density and low cp surface will reach quite fast the skin temperature. If it feels cold, it has to remove heat from the skin, so the thermal conductivity is decisive --Eio (talk) 08:47, 11 November 2016 (UTC)

References

Symbol usage

Symbols $\kappa$ and $k$ for thermal diffusivity and thermal conductivity look very similar, and k is widely used for almost any coefficient. I suggest to use D and $\lambda$ instead. The formula would be:

$D={\lambda \over {\rho c_{p}}}$

${\alpha }$ is widely used for Thermal diffusivity --pR@tz (talk) 15:39, 15 March 2008 (UTC)

any body can tel me the thermal diffusivity of steel?

thanks Kerke0ba (talk) 14:50, 30 May 2008 (UTC)

I don't know about the rest of you, but although kappa and k look alike, I see kappa way more than alpha for thermal diffusivity. Should it be changed back? Awickert (talk) 22:37, 9 December 2008 (UTC)

Come to think of it, I've never seen alpha for thermal diffusivity, but have seen it many, many times as the coefficient of thermal expansion, which (if this is the dominant usage) could cause confusion. Awickert (talk) 22:39, 9 December 2008 (UTC)

I suggest to skip $k$ and $\kappa$ for the denotion of thermal diffusivity, because in the formula below they are already used for thermal conductivity. To me that seems contradictory. Stonovic (talk) 14:32, 23 February 2012 (UTC)

From my point of view, it is quite sufficient to use a for thermal diffusivity:

$a={\lambda \over {\rho c_{p}}}$

I agree with Awickert, that alpha is often used for the coefficient of thermal expansion. For me D is more a diffusion coefficent.Stonovic (talk) 08:34, 14 March 2012 (UTC)

table of values

I like how the table of thermal diffusivity values lists them in random order, and duplicates the entry for air. — Preceding unsigned comment added by 71.103.149.123 (talk) 06:34, 12 September 2011 (UTC)

Thermal diffusivity of water is wrong. The right is 0,0014 --193.221.89.14 (talk) 13:21, 30 September 2011 (UTC)

Why not a table of k???

That would make sense?131.211.151.19 (talk) 12:49, 14 March 2012 (UTC)

• as shown here: List_of_thermal_conductivities? Stonovic (talk) 09:06, 15 March 2012 (UTC)

Unit analysis

Doing a simple unit analysis of the definition given in the first section of this page suggests /something/ is off. Not sure what (I haven't had a chance to look into it), but ( W / (m^2 K) ) / ((kg / m^3) (J / kg K)) comes out to m / s, not the m^2 / s listed as the SI unit for thermal diffusivity in the end of the first paragraph. — Preceding unsigned comment added by 99.224.222.199 (talk) 20:15, 8 February 2014 (UTC)

Assessment comment

The comment(s) below were originally left at Talk:Thermal diffusivity/Comments, and are posted here for posterity. Following several discussions in past years, these subpages are now deprecated. The comments may be irrelevant or outdated; if so, please feel free to remove this section.

any body can tel me the thermal diffusivity of steel? thanks

Last edited at 15:25, 30 May 2008 (UTC). Substituted at 08:33, 30 April 2016 (UTC)

"It is approximately analogous to whether a material is "cold to the touch"[citation needed]"

That's just wrong. Effusivity is related to whether a material is cold to the touch or not, not diffusivity. A material with negligible heat capacity immediately assumes the temperature of the body and therefore does not feel cold or hot, even though it has a diffusivity which is enormously larger than e.g. aluminum. — Preceding unsigned comment added by 157.193.65.173 (talk) 11:17, 13 February 2017 (UTC)